Product Description And Specifications; Product Features; Technical Data; Dust/Chip Extraction - Bosch GSG 300 Professional Notice Originale

OBJ_BUCH-75-003.book Page 7 Wednesday, October 19, 2016 10:32 AM
Safety Warnings for Foam Rubber Cutters
 Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting ac-
cessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator an
electric shock.
 Keep hands away from the sawing range. Do not reach
under the workpiece. Contact with the saw blade can
lead to injuries.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for the cutting of flexible foamed ma-
terials made of plastic, rubber or similar materials.

Product Features

The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 On/Off switch
2 Saw blade guide*
3 Saw blade pair*
4 Base plate
5 Handle (insulated gripping surface)
6 Screw
7 Cover plate
8 Knurled screw
9 Tensioning screw for base plate
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Bosch Power Tools

Technical Data

Foam rubber cutter
Article number
Rated power input
Output power
Stroke rate at no load n
0
Stroke speed under load
Cutting depth, max.
Weight according to EPTA-
Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Assembly
 Before any work on the machine itself, pull the mains
plug.
Mounting the Saw Blade Guide (see figure A)
Remove the screws 6 from the housing. Attach the saw blade
guide 2 onto the housing in such a manner that the mounting
pins engage into the corresponding holes and secure with the
screws 6.
Inserting/Replacing Saw Blades (see figure B)
 Wear protective gloves when mounting the saw blades.
Danger of injury when touching the saw blades.
Loosen and remove the knurled screws 8 together with the
spring washers and the cover plate 7.
 Firstly, insert the saw blade pair 3 into the bottom of the
saw blade guide 2, paying attention that the longitudinal
grooves of the saw blades engage into the guide pin of
the saw blade guide.
 Secondly, locate the top of the saw blade pair 3 onto the
drive tappets, ensuring that the saw blades are properly
seated in the saw blade guide.
Place the cover plate 7 onto the set screws on the housing and
secure them with the knurled screws 8, ensuring that the
spring washers have also been mounted.
Mounting the Base Plate (see figure C)
Insert the saw blade guide 2 into the corresponding notch on
the base plate 4. Tighten the tensioning screw 9.

Dust/Chip Extraction

 Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
English | 7
GSG 300
0 601 575 1..
W 350
W 185
-1
min 3500
-1
min 2100
mm 300
kg 1.6
/II
1 609 92A 38G | (19.10.16)