Danfoss VLT AutomationDrive FC 302 Low Harmonic Drive Manuel D'utilisation page 118

Programmation
6.4.7 AF Settings 300-**
AVIS!
Except for 300-10 Tens° nom. du filtre actif, it is not recommended to change the settings in this parameter group for
the Low Harmonic Drive
N° par. # Description du paramètre
300-0* General Settings
300-00 Harmonic cancellation mode
300-01 Compensation priority
300-08 Lagging reactive current
300-1* Network Settings
6 6
300-10 Active filter nominal voltage
300-2* CT Settings
300-20 CT primary rating
300-24 CT Sequence
300-25 CT Polarity
300-26 CT Placement
300-27 Number of CTs per phase
300-29 Start auto CT detection
300-3* Compensation
300-30 Compensation points
300-35 Cosphi reference
300-4* Paralleling
300-40 Master follower selection
300-41 Follower ID
300-42 Num. of follower AFs
300-5* Sleep Mode
300-50 Enable sleep mode
300-51 Sleep mode trig source
300-52 Sleep mode wake up trigger
300-53 Sleep mode sleep trigger
6.4.8 AF Readouts 301-**
N° par. # Description du paramètre
301-0* Output Currents
301-00 Output current [A]
301-01 Output current [%]
301-1* Unit Performance
301-10 THD of current [%]
301-12 Power factor
301-13 Cosphi
301-14 Leftover currents
301-2* Mains Status
301-20 Mains current [A]
301-21 Mains frequency
301-22 Fund. mains current [A]
116
Manuel d'utilisation
Valeur par défaut
[0] Overall
[0] Harmonics
[0] Disabled
ExpressionLimit
ExpressionLimit
[0] L1, L2, L3
[0] Normal
[1] Load Current
1
[0] Off
0.0 A
0.500 N/A
[2] Not Paralleled
1 N/A
1 N/A
null
[0] Mains current
ExpressionLimit
80 %
Valeur par défaut
0.00 A
0.0 %
0.0 %
0.00 N/A
0.00 N/A
0.0 A
0 A
0 Hz
0 A
Danfoss A/S © Rév. 2014-02-07 Tous droits réservés.
4 process Changement
pendant le conversion
fonctionnement
All set-ups TRUE
All set-ups TRUE
All set-ups FALSE
2 set-ups FALSE
2 set-ups FALSE
2 set-ups FALSE
2 set-ups FALSE
2 set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups TRUE
All set-ups TRUE
2 set-ups FALSE
2 set-ups FALSE
2 set-ups FALSE
2 set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
4 process Changeme Indice de
nt pendant conversio
le fonction-
nement
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
Indice de Type
- Uint8
- Uint8
Uint8
0 Uint32
0 Uint32
- Uint8
- Uint8
- Uint8
Uint8
- Uint8
-1 Uint32
-3 Uint16
- Uint8
0 Uint32
0 Uint32
- Uint8
- Uint8
0 Uint32
0 Uint32
Type
n
-2 Int32
-1 Int32
-1 Uint16
-2 Uint16
-2 Int16
-1 Uint32
0 Int32
0 Uint8
0 Int32
MG37A204