Scheppach HS110 Traduction Des Instructions D'origine page 36

Installing the guide rail (Fig.13+14)
1. Fit the coach bolts (b) in the respective drilled
holes in the work table and the table extensions,
by securing these from the rear with the flange
nuts (e).
2. Tighten the flange nuts (e) lightly.
3. Connect both guide rails (15,15a).
4. Slide the connected guide rails over the guide
groove on the rear, over the coach bolts (b), until
they sit central to the table surface.
Aligning the guide rail (Fig.13+14)
1. Turn the saw blade to the maximum position out of
the saw table, by turning the crank clockwise until
it reaches the stop.
2. Position the parallel stop with an opened eccen-
tric lever (13) on the guide rails (15) on the saw
table and secure it at the 0 position, by pressing
the eccentric lever (13) fully downwards.
3. Slide the connected guide rails sufficiently far to
the left, until the parallel stop reaches the right
outside of the saw blade.
4. Now tighten the flange nuts (e) firmly to fix this
position.
5. Now fit the end caps (15b) on both sides of the
guide rail .
Mounting / adjusting the Riving Knife
Insert the battery (Figures 15-19)
Caution! Remove the mains plug! The setting of
the saw blade (4) must be checked whenever a
blade has been replaced.
1. Adjust the saw blade (4) to a max. cutting depth,
move to the 0° position and lock in place.
2. Dismantle the saw blade guard (2) (not during in-
itial assembly).
3. Release the two attachment bolts (25) and re-
move the table insert (5).
4. Loosen the fixing screw (26) (use the open-ended
spanner AF8 supplied).
5. Push the riving knife (3) upwards.
6. The distance between the saw blade (4) and riv-
ing knife (3) should be between 3 mm and max. 5
mm, (Figure. 18)
7. Retighten the attachment bolts (26) and mount
the table insert (5).
8. Mount the saw blade guard (2) with the screw and
knurled nut and flat washer (27).
Mounting / dismounting the Saw Blade Guard
(Fig. 18)
On irst assembly, the assembly of the saw blade
protection has already been carried out in the
previous assembly step.
1. Loosen the nut and wing nut (27) of the saw blade
guard (2). Place the saw blade guard (2) from the
top onto the riving knife (3).
36 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
2. Mount the bolt with the nut and washer (27) so
that the bolt sits irmly in the slot.
3. Do not overtighten the bolt (27) The saw blade
guard must be able to move freely.
4. Dismantling is carried out in reverse order. Cau-
tion! Before you start sawing, the saw blade guard
(2) has to be lowered onto the item being sawn.
Replacing the Table Insert (Fig.19)
1. If it is worn or damaged, the table insert (5) has to
be replaced, as otherwise there is an increased
risk of injury.
2. Remove the screw (25) using a slotted screwdriver.
3. Take out the table insert (5).
4. The new table insert is mounted in reverse order.
Attaching/changing the Saw Blade (Fig. 19,20)
1. Caution! Remove the mains plug and wear
protective gloves.
2. Dismantle the saw blade guard (2).
3. Remove the table insert (5) by releasing the two
countersunk screws (25).
4. Place the hexagon socket key (i) (HX 6) on the
bolt and use the jaw spanner (g) (SW 22) to stop
the motor spindle from turning.
5. Caution! Turn the bolt in the direction of rotation
of the saw blade. Remove the loosened screw.
6. Remove the outer lange and take the old saw
blade off the inner lange by pulling downwards
and diagonally
7. Clean the saw blade langes carefully with a wire
brush before attaching the new saw blade..
8. Insert and tighten the new saw blade in reverse order.
Caution! Note the direction of motion; the
slope of the cutting edge of the teeth must
face the direction of motion, i.e. forwards
(see the arrow on the saw blade guard.
9. Reattach and adjust the table insert (5) and the
saw blade guard (2).
10. Before you work with the saw again, a check must
be carried out to ensure that the protective devic-
es are working properly.
Connect the suction device
1. Attach a suction hose to the suction adapter (16).
If necessary, secure the suction hose with a hose
clamp to prevent it from slipping off the suction
adapter (16).
2. A household vacuum cleaner is not suitable as
a suction device. Use a multi-purpose vacuum
cleaner or a swarf extraction machine.