Assembly And Adjustments - DeWalt DW756 Guide D'utilisation

English
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be
caught in moving parts.
• An extension cord must have adequate wire size
(AWG or American Wire Gauge) for safety. The smaller
the gauge number of the wire, the greater the capacity
of the cable, that is, 16 gauge has more capacity than 18
gauge. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. When using
more than one extension to make up the total length,
be sure each individual extension contains at least the
minimum wire size. The following table shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The
lower the gauge number, the heavier the cord.
Minimum gauge for Cord sets
Total length of Cord in Feet
Volts
120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
More not
American Wire gauge
Than More
Than
0 6 18
6 10 18
10 12 16
12 16 14
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
n o ....................... no load speed
(grounded)
n ......................... rated speed
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. D WALT tools are factory tested;
e
if this tool does not operate, check power supply.
4
All manuals and user guides at all-guides.com
Bench grinder
COMPONENTS (FIG. A)

Refer to Figure A at the beginning of this manual for a
complete list of components.
Intended Use
This bench grinder is designed for professional applications.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
This bench grinder is a professional power tool. DO nOT
(meters)
let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.

ASSEMBLY AND ADJUSTMENTS


16 16 14
16 14 12
16 14 12
Bench Mounting
12 Not Recommended
1. The grinder should be unplugged.
2. Remove the drilling template from this manual
or AC/DC .... alternating or
direct current
...................... Class II
Construction 3. Using a center punch, transfer the hole centers
(double insulated)
4. Drill appropriate sized holes.
5. Insert M8 hex head bolts through washers and the
...................... earthing terminal
..................... safety alert symbol
6. Tighten the nuts. Do not overtighten. Allow the rubber
..................... visible radiation
..................... wear respiratory
Installing Tool Rests (Fig. F)
protection
..................... wear eye
There is a left and right tool rest. First secure the tool rest
protection
to the bracket
washer
..................... wear hearing
protection
For the DW756, an additional spacer
..................... read all washer
documentation
Next, for the DW756 and the DW758, secure the bracket/
tool rest assembly to the wheel guard
1/4"-20 UNC bolts
Proceed to install the other tool rest using the
same description.

nOTE: When in use, the tool rests should be adjusted
to within 1/8" (3.18 mm) of the grinding wheel or other
accessory being used.
SPECIFICATIONS
DW756
6" (152 mm)
Arbor 1/2" (13 mm)
RPM 3450
WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
(page 26) and place it in position of the bench. Check
for the availability of power for the grinder. Tape the
template to the bench.
for drilling.
holes. You may want to use washers on the underside of
the bench as well.
feet to absorb the vibration when the grinder is running.
7 using the hex bolt 8
, external tooth washer
10 11
12
11 are required, as shown in Figure F.
14 , and two flat washers
CAUTION: Longer bolts may interfere with the
movement of the grinding wheel.
DW758
8" (200 mm)
5/8" (16 mm)
3600
4
, spring washer 9 , flat
and nut .
13
and external tooth
28 using the two
10 .