Safety Instructions; Work Area Safety; Electrical Safety; Personal Safety - Hilti AG 125-A22 Mode D'emploi

Noise information (as perEN 60745‑2‑3):
Typical A-weighted sound power level
Typical A-weighted emission sound pressure level
Uncertainty for the given sound level
Vibration information in accordance with EN 60745
en Triaxial vibration value (vibration vector sum) for the
AG 125‑A22
Surface grinding using the vibration-absorbing side
handle, a
h,AG
Uncertainty (K)
Additional information

5 Safety instructions

NOTE
The safety rules in section 5.1 contain all general safety
rules for power tools which, in accordance with the
applicable standards, must be listed in the operating
instructions. Accordingly, some of the rules listed may
not be relevant to this tool.
5.1 General power tool safety warnings
a)
WARNING
Read all safety warnings and all instructions. Fail-
ure to follow the warnings and instructions may result
in electric shock, fire and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to
your mains-operated (corded) power tool or battery-
operated (cordless) power tool.

5.1.1 Work area safety

a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.

5.1.2 Electrical safety

a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any ad-
apter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
22
All manuals and user guides at all-guides.com
94 dB (A)
83 dB (A)
3 dB (A)
Measured in accordance with EN 60745‑2‑3
3.8 m/s²
1.5 m/s²
Other applications, such as cutting, may produce vibra-
tion values that deviate from the given values.
c) Do not expose power tools to rain or wet condi-
d) Do not abuse the cord. Never use the cord for
e) When operating a power tool outdoors, use an
f)

5.1.3 Personal safety

a) Stay alert, watch what you are doing and use
b) Use personal protective equipment. Always wear
c) Prevent unintentional starting. Ensure the switch
d) Remove any adjusting key or wrench before turn-
tions. Water entering a power tool will increase the
risk of electric shock.
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
is in the off‐position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
ing the power tool on. A wrench or a key left at-
tached to a rotating part of the power tool may result
in personal injury.