Technical Data; Safety Instructions; Work Area Safety; Personal Safety - Hilti DEG 500-D Mode D'emploi

4 Technical data

Right of technical changes reserved.
Tool
Rated current input
Rated frequency
Rated speed
Cutting discs (Ø)
Dimensions (L x H x W) without
hood
Weight without accessories
Other information about the power tool
Drive spindle thread (arbor size)
Spindle length
Protection class

5 Safety instructions

NOTE
The safety rules in section 5.1 contain all general safety
rules for power tools which, in accordance with the
applicable standards, require to be listed in the operating
instructions. Accordingly, some of the rules listed may
not be relevant to this tool.
5.1 General Power Tool Safety Warnings
a)
WARNING
Read all safety warnings and instructions. Failure
to follow the warnings and instructions may result
in electric shock, fire and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to
your mains-operated (corded) power tool or battery-
operated (cordless) power tool.

5.1.1 Work area safety

a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.

5.1.2 Electrical safety

a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Un-
modified plugs and matching outlets will reduce risk
of electric shock.
All manuals and user guides at all-guides.com
DEG 500-D
Rated voltage 120 V: 11.5 A
60 Hz
11,000/min
125 mm (5")
360 mm (14.17") x 103 mm (4.06") x
80 mm (3.15")
1.9 kg (4.19 lb)
⁵⁄₈"‑11 UNC
⁶⁄₈"
Protection class II (double insulated)
b) Avoid body contact with earthed or grounded
c) Do not expose power tools to rain or wet condi-
d) Do not abuse the cord. Never use the cord for
e) When operating a power tool outdoors, use an
f)

5.1.3 Personal safety

a) Stay alert, watch what you are doing and use
b) Use personal protective equipment. Always wear
c) Prevent unintentional starting. Ensure the switch
DEG 600-D/-P
Rated voltage 120 V: 11.5 A
60 Hz
9,300/min
150 mm (6")
360 mm (14.17") x 103 mm (4.06") x
80 mm (3.15")
1.9 kg (4.19 lb)
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
tions. Water entering a power tool will increase the
risk of electric shock.
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
is in the off‐position before connecting to power
source and/or battery pack, picking up or carrying
en
5