Setting The Temperature; Ironing With Steam - Bosch Sensixx B22L Notice D'utilisation

Preparations
1. Release the iron from its lock system (13) by pulling
the lever located at the heel of the iron backwards.
2. Remove any label or protective covering from the
soleplate.
3. Place the appliance horizontally on a solid, stable
surface. You may remove the iron pad from the
appliance and place the iron on it on another solid,
stable, horizontal surface.
4. Fill the water tank, making sure not to pass the level
mark.
5. Unwind the mains cable (6) fully and plug it into an
earthed socket.
6. Set the main power button (12) to the on position
(illuminated in red).
7. The "Steam ready" indicator lamp (9) will light up after
several minutes, indicating that the appliance is ready
to use.
The steam generator will take more time to reach
"Steam ready" state only upon the initial heating
up, or after performing the desscaling operation
(Calc'n'Clean).
When water is already present in the steam generator
during regular use, heat up time to reach the operating
temperature will be faster.
8. This appliance has a builtsin water level sensor. The
"refill water tank" indicator (11) will light when the
water tank is empty.
Important:
• Normal tap water can be used.
To prolong the optimum steam function, mix tap water
with distilled water 1:1. If the tap water in your district
is very hard, mix tap water with distilled water 1:2.
You can inquire about the water hardness with your
local water supplier.
• The water tank can be filled at any time while using the
appliance.
• To avoid damage and/or contamination of the water tank
and the boiler, do not put perfume, vinegar, starch, dess s
caling agents, additives or any other type of chemical
product into the water tank.
Any damage caused by the use of the
aforementioned products, will make the guarantee
void.
• The iron is not designed to rest on its heal. Please
always position it horizontally on the iron pad (2).
• The iron pad can be placed into the specially designed
recess on the appliance or somewhere suitable
alongside the ironing area.
Never rest the iron on the appliance without the
iron pad!.
• During it first use the iron may produce certain vapours
and odours, along with white particles on the soleplate,
this is normal and it will stop after a few minutes
• While the steam release button is pressed, the water
tank may produce a pumping sound, this is normal,
indicating that water is being pumped to the steam
tank.
All manuals and user guides at all-guides.com
(A) Setting the temperature
1. Check the ironing instruction label on the garment to
2. Turn the temperature selector (15) to the required
3. The indicator lamp (18) will remain lit while the iron is
Tips:
• Sort your garments out based on their cleaning
• If you are not sure what the garment is made of then
Ironing with steam
The steam control is used to adjust the amount of
steam produced when ironing.
1. Turn the temperature selector (15) to the required
2. Set the amount of steam to suit your needs, using
3. Press the steam (16s17*) release button to release
Attention:
When ironing on a lower temperature setting "•".
• If the appliance has variable steam control (10*), set
• If the appliance does not have variable steam control,
In both cases, if you find that water is dripping out of the
soleplate, set the temperature selector (15) to a higher
position (take care that the garment can be ironed on
this heat temperature setting).
• At the beginning of each use, it is possible that drops
determine the correct ironing temperature.
setting:
• Synthetics
•• Silk – Wool
••• Cotton – Linen
heating and go out as soon as the iron has reached
the selected temperature.
symbol labels, always starting with clothes that have
to be ironed at the lowest temperatures.
begin ironing at a low temperature and decide on the
correct temperature by ironing a small section not
usually seen when worn
setting.
the variable steam control (10*) (depending on the
model).
For normal use, please choose one of the following
recommended settings:
Temperature Steam setting
•
••
•••
steam.
the variable steam control to its lowest position
press the steam release button only for a few seconds
at a time when ironing at lower temperatures.
of water will be dispensed alongside steam.
Therefore, it is advisable to try the iron on the ironing
board or a piece of cloth to start with.
en
(B)
.
11