Bosch Sensixx B22L Notice D'utilisation page 12

en
"Pulse steam" function
This appliance has a special function for tackling difficult
creases.
The "Pulse steam" function helps soften stubborn
garments like jeans or linen faster.
When the steam release button is activated, the steam
generator will release three powerful shots of steam so
that the steam reaches even deeper into the fabrics.
1. Set the temperature selector (15) on "• • •"
2. Briefly press the steam shot button (17*) on the top of
the handle.
or (model dependent)
Press the steam release button (16) on the bottom
of the handle two times in quick succession (doubles
click).
Remarks:
• It is possible to stop the shots of steam by quickly
pressing the steam button again.
• Some water drops may appear when you use the
"Pulse steam" function for the first time.
The water drops will disappear after you have used
the function for some time.
Ironing without steam
1. Begin ironing but without pressing the steam release
button.
Vertical steam
This can be used to remove creases from hanging
clothes, curtains etc.
Warning!:
• Never direct the steam jet at garments that are
being worn.
• Never aim the steam at people or animals.
1. Set the temperature to the "•••" setting.
2. Hold the iron in an upright position 15 cm away from
the garment being steamed.
3. You can steam iron curtains and hanging garments
(jackets, suits, coats...) by placing the iron in a vertical
position and pressing the steam release button (16 or
17*).
"Intelligent steam" function
(model dependent)
This system has intelligent steam control, which, after
releasing the steam release button (16), provides a small
amount of additional steam.
The additional steam can always be stopped by briefly
pressing the steam release button once again.
12
All manuals and user guides at all-guides.com
Energy saving
(model dependent)
If the "Energy saving" button (8) is switched on, you
can save up to 25% of the energy and 40% of the water
consumption (*), and still achieve good results when
ironing most of your garments.
It is advisable to use the normal energy setting only for
thick and very wrinkled fabrics.
(*) In comparison to the maximum setting.
Note: If you work with the "Energy saving" function,
the variable steam regulation and temperature
regulation can still be used as recommended.
Auto shutmoff
(model dependent)
If during ironing, the steam release button (16s17*) on the
iron handle is not pressed for a certain length of time (8
minutes), the steam station will automatically switch off.
The "auto shutsoff" pilot lamp (9) will flash when auto
shutsoff has been activated.
To switch the steam station back on, press the steam
release button again.
Fabric protection
soleplate cover
(model dependent)
(C)
The fabricsprotection soleplate cover (20*) is used for
steamsironing delicate garments at maximum temperature
without damaging them. Use of the soleplate cover also
does away with the need for a cloth to prevent shine on
dark materials.
It is advisable to first iron a small section on the inside of
the garment to see if it is suitable.
To attach the soleplate cover to the iron, place the tip
of the iron into the end of the soleplate cover and pull
the elastic strap over the lower rear of the iron until it
fits tightly. To release the soleplate cover, pull the elastic
strap and remove the iron.
The fabricsprotection soleplate cover may be purchased
from our customer service or from our website
Calc'n'Clean Advanced
Cleaning the Boiler
To extend the life of your steam generator and to prevent
any build up of scale, it is essential that you rinse out the
filter (4*) and the boiler after several hours of use. If the
water is hard, increase the frequency.
Do not use descaling agents for rinsing out the boiler, as
they could damage it.
button
Accessory code Name of accessory
(Afterssales) (online shop)
571510
(D)
TDZ2045
(E)