Publicité
Les langues disponibles
Les langues disponibles
EngLIsh
6) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
b ) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
Additional Safety Instructions for Chipping
Hammers
Wear ear protectors. Exposure to noise can cause
•
hearing loss.
•
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
•
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the tool "live" and could give the operator an
electric shock.
•
Be certain that the material being drilled does not conceal
electric or gas service and that their locations have been
verified with the utility companies.
•
Keep a firm grip on the tool at all times. Do not attempt
to operate this tool without holding it with both hands.
Operating this tool with one hand will result in loss of control.
Breaking through or encountering hard materials such as
re-bar may be hazardous as well. Tighten the side handle
securely before use.
•
Ensure the chisel is secured in place before operating the tool.
•
In cold-weather conditions or when the tool has not been used
for a longer period of time, let the tool run with no load for
several minutes before use.
•
When working above ground level ensure the area below
is clear.
•
Do not touch the chisel or the parts close to the chisel
immediately after operation, as they may be extremely hot
and cause burns to the skin.
•
Always direct the power cable to the rear, away from
the chisel.
•
Do not operate this tool for long periods of time.
Vibration caused by hammer action may be harmful to your
hands and arms. Use gloves to provide extra cushion and limit
exposure by taking frequent rest periods.
Residual Risks
The following risks are inherent to the use of hammers:
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
•
Impairment of hearing.
•
Risk of squeezing fingers when changing the accessory.
•
Health hazards caused by breathing dust developed when
working in concrete and/or masonry.
28
•
Risk of personal injury due to flying particles.
•
Risk of burns due to accessories becoming hot
during operation.
•
Risk of personal injury due to prolonged use.
Chargers
WALT chargers require no adjustment and are designed to be
D
E
as easy as possible to operate.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
i
your charger corresponds to that of your mains.
YourD
WALTcharger is double insulated in accordance
E
with EN60335; therefore no earth wire is required.
If the supply cord is damaged, it must be replaced
only by D
WALT or an authorised service organisation.
E
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
•
Safely dispose of the old plug.
•
Connect the brown lead to the live terminal in the plug.
•
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for the
power input of your charger (see Technical Data). The minimum
conductor size is 1 mm
; the maximum length is 30 m.
2
When using a cable reel, always unwind the cable completely.
Important Safety Instructions for All Battery Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for compatible battery
chargers (refer to Technical Data).
•
Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
battery pack.
WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Electric shock may result.
WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
CAUTION: Burn hazard. To reduce the risk of injury,
charge only D
WALT rechargeable batteries. Other types of
E
batteries may burst causing personal injury and damage.
CAUTION: Children should be supervised to ensure that
they do not play with the appliance.
NOTICE: Under certain conditions, with the charger
plugged into the power supply, the exposed charging
contacts inside the charger can be shorted by foreign
material. Foreign materials of a conductive nature such
Publicité
