DeWalt DCH832 Traduction De La Notice D'instructions Originale page 27

HEAVY‑DUTY CHIPPING HAMMER
DCH832, DCH892
Congratulations!
You have chosen a D WALT tool. Years of experience, thorough
E
product development and innovation make D
most reliable partners for professional power tool users.
Technical Data
Voltage
Type
Battery type
No‑load beats per minute
Single impact energy (EPTA 05/2009)
Variable Speed Dial
Variable Speed Dial Positions
Dust Extractor
Bit holder
Wireless Tool Control Transmitter
Frequency Band
Max. Power (EIRP)
Length
Width
Height
Weight (without battery pack)
Noise values and vibration values (triax vector sum) according to EN60745‑2‑6:
L (emission sound pressure level) dB(A)
PA
L (sound power level)
WA
K (uncertainty for the given
sound level)
Chiselling
Vibration emission value a
h ,Cheq
=
Uncertainty K =
* Measured at the side handle. Side handle vibration is higher than vibration at
the main handle.
The vibration and/or noise emission level given in this information
sheet has been measured in accordance with a standardised test
given in EN60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure.

WARNING: The declared vibration and/or noise emission
level represents the main applications of the tool. However
if the tool is used for different applications, with different
accessories or poorly maintained, the vibration and/or
noise emission may differ. This may significantly increase
the exposure level over the total working period.
WALT one of the
E
DCH832 DCH892
V 54 54
DC
1 1
Li‑Ion Li‑Ion
bpm 1450–2900 1105–2210
J 10.5 19.4
Yes Yes
7 7
DWH051 DWH051
SDS max® SDS max®
MHz 433 433
mW 0.03 0.03
mm 556 627
mm 112 115
mm 253 266
kg 6.5 8.9
92 93
dB(A) 103 104
dB(A) 3 3
m/s² 8.7 9.4
m/s² 1.5 1.5
An estimation of the level of exposure to vibration and/or
noise should also take into account the times when the tool
is switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration and/or noise such as: maintain
the tool and the accessories, keep the hands warm
(relevant for vibration), organisation of work patterns.
EC‑Declaration of Conformity
Machinery Directive and Radio Equipment
Directive
Heavy-Duty Chipping Hammer
DCH832, DCH892
WALT declares that these products described under
D
E
Technical Data are in compliance with: 2006/42/EC,
EN60745‑1:2009+A11:2010, EN60745‑2‑6:2010.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact D
the following address or refer to the back of the manual.
2000/14/EC, Electrical concrete breaker (hand‑held), m ≤ 15 kg,
Annex VIII, TÜV Rheinland LGA Products GmbH (0197), D‑90431
Nürnberg, Germany, Notified Body ID No.: 0197
Level of sound power according to 2000/14/EC (Article 12,
Annex III, No. 10; m ≤ 15 kg):
L (measured sound power level)
WA
DCH832
DCH892
L (guaranteed sound power level)
WA
Markus Rompel
Vice President of Engineering, PTE‑Europe
WALT, Richard‑Klinger‑Straße 11,
D
E
65510, Idstein, Germany
01.12.2021
DECLARATION OF CONFORMITY
THE SUPPLY OF MACHINERY (SAFETY)
REGULATIONS 2008
EngLIsh
WALT at
E
103 dB
104 dB
103 dB
25