Seat; Wheelbase Extension; Wheel Tracking; Backrest - Quickie Neon Fix Front Notice D'utilisation

Options – Seat height
Adjusting the seat height (7.53.2)
To adjust rear seat height, slacken
and remove the 4 Torx screws (A)
(2 each side) and the thread
washer (B), which secures the
clamp (C) for the camber tubes to
the axle plates (D). Adjust the two
camber tube clamps (C) to the
required height and replace the 4
Torx screws. Before tightening the
screws, please follow the instruc-
tions for setting the toe-in/toe-out
to zero (section 7.61.1).
Tighten the screws to 10 Nm.
NOTE – An adjustment to the castor angle may
be necessary when adjusting the rear seat
height.
Setting the centre of gravity of
(7.54.4)
the seat
Undo both screws (1) (2 on each
side) and make the desired adjust-
ment to the axle adapter on the
axle plate. Always make sure that
you have selected the same sett-
ing on both sides. Tighten the
screws to 10 Nm.
CAUTION!
Brakes must be adjusted to suit the new position!
Setting the centre of gravity of
the seat with medium and long
axle plates (7.54.5)
Undo both screws (3) (2 on each
side), and for the NEON with
swing-away footrests, also undo
the screw (4). Move the perforated
plate to the required position.
Always make sure that you have
selected the same setting on both
sides. Insert the screws and tigh-
ten to 7 Nm. Then undo the screws
under the seat tube and put the
seat tube back into the required
position. The screws must be tigh-
tened to 7 Nm.
CAUTION!
The markings on the right and
left seat tube must be in the same position on
the rear edge.
14.06.10 Neon Rev.3
Options – wheelbase extension
Wheelbase extension for
(7.56.2)
amputees
Using the amputee adapter, the
wheelbase can be extended by
10.5 cm. Make sure that after any
adjustment work, all screws are
tightened correctly (see the page
on torque).
CAUTION!
Wheel locks must be adjusted to suit the new
position!
Options – Wheel tracking
Adjusting the wheel tracking
Fundamentals: To achieve the very
best movement, the rear wheels
must be adjusted to their optimum
setting. To ensure this, the wheel
tracking must be adjusted correct-
ly. To do this, measure both wheels
to check they are parallel. The dif-
ference between both measurements should not be
more than 5 mm. By undoing the screws and turning
the adapter, you can adjust the wheels to be parallel.
Make sure that after any adjustment work, all screws
are tightened correctly (see the page on torque).
CAUTION!
Be careful, there is a risk of tipping when adjusting
the centre of gravity of the seat!
Options – Back
Angle adjustment of the folding backrest:
1. Open the upper screws and
loosen the screw connection
(Figure 1).
2. The hole in the back tube must
be lined up with the hole in the
connecting part, such that you
can set the desired backrest
angle (Figure 2).
3. Fit the screw connection with
the nut and washer until they are
hand tight, so that there is no
lateral play between the compo-
nents. But you must still be able
to fold the back tube down
easily.
4. Set the folding mechanism: To
do this, loosen the nuts on the
cam slightly (Figure 3). Set the
cam (component 1) such that
the folding mechanism locks
into place with no play (if
necessary use a 10 mm open-
ended spanner to do this). Then
hold the cam in position and
tighten the nuts (5 Nm).
5. Repeat steps 1 to 4 for the
second side.
Figure 1
Figure 2
Figure 3
11
NEON