EINHELL GC-PM 46 SM HW-E Li Instructions D'origine page 23

Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Damage to hearing if no suitable ear protec-
tion is used.
2. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
5.1 Assembling the components
Some parts of the equipment come disassem-
bled. For quick and easy assembly, read and
follow the instructions below.
Note! You will need the following additional tools
(not supplied) for assembly, and also for mainte-
nance work:
•
One flat oil drip tray (for changing the oil)
•
One 1 liter measuring jug (oil/petrol resistant)
•
One petrol can
•
One funnel (suitable for the tank's petrol filler
neck)
•
Household wipes (to wipe up oil/petrol resi-
due; dispose of these at a filling station)
•
One petrol suction pump (plastic, available
from DIY stores)
•
One oil can with hand pump (available from
DIY stores)
•
Engine oil
Assembly
1. Fit the push bar (Item 3) as shown in Fig.
3a-3b. For fastening choose one of the holes
(Fig. 3a/Item A) to suit the required height of
the handle.
Important! The identical height must be set
Anl_GC_PM_46_SM_HW_E_Li_SPK13.indb 23
GB
on both sides.
2. Fit the Power-X combi-panel (Item 15) with
the supplied screws as shown in Fig. (3c and
3d).
3. Insert the grip of the starter cable (Item 9) into
the hook provided for that purpose as shown
in Fig. 1.
4. Fasten the actuator cables to the push bar
with the supplied cable clips (Items 10a and
10b) as shown in Fig. 3e.
5. Lift the ejector fl ap (Item 5a) with one hand
and hook in the grass bag (Item 4a) as shown
in Fig. 4a.
5.2 Adjusting the cutting height
Warning! Adjust the cutting height only when
the engine has been switched off .
•
The cutting height is centrally adjusted with
the cutting height adjustor lever (Fig. 7/Item
8). Different cutting heights can be selected.
•
Actuate the adjustor lever and pull it to the
required position. Let the lever click into po-
sition.
Fit the battery pack (Item 17) and safety plug
(Item 16) as shown in Fig. 3f.
5.3 Charging the Li battery pack (Fig. 3f-13)
Important!
The charger is allowed to be used only for the li-
thium-ion batteries of the Power-X-Change series!
The battery is protected from exhaustive dischar-
ge. An integrated protective circuit automatically
switches off the equipment when the battery is
fl at.
Warning! Do not actuate the On/Off switch any
more if the protective circuit has tripped. This may
damage the battery.
1. Remove the battery pack from the handle,
pressing the pushlock button (18) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(11) into the socket outlet. The green LED will
then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
4. In section „Charger indicator" you will fi nd a
table with an explanation of the LED indicator
on the charger.
- 23 -
15.10.2021 08:32:29