Bosch GNA 2,0 Professional Notice Originale page 5

Keep cutting tools sharp and clean. Properly main-
u
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
u
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
u
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety instructions for nibblers
This power tool is not suitable for bench-mounted use.
u
It must not be clamped into a vice or fastened to a work-
bench, for example.
Wear protective gloves during work and pay particu-
u
lar attention to the cord. Sharp burrs develop on the cut
sheets; these can cause injury or damage the cord.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for cutting sheet metal without
deforming the material and is suitable for straight cuts, cut-
outs and narrow curves.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) On/off switch
(2) Cap nut for die
Bosch Power Tools
(3) Clamping screw for die
(4) Die
(5) Punch
(6) Hollow screw for fastening of punch
Technical Data
Nibbler
Article number
Rated power input
Power output
No-load stroke rate n
0
Stroke speed under load
A)
Max. sheet cutting capacity
Cutting width
Smallest curve radius
Weight according to
EPTA-Procedure 01:2014
Protection class
A) with reference to steel sheet of up to 400 N/mm
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Operation
Products that are only sold in AUS and NZ: Use a resid-
u
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Starting Operation
Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
Switching On and Off
To switch on the power tool, slide the on/off switch (1) for-
wards so that I appears on the switch.
To switch off the power tool, slide the on/off switch (1)
backwards so that 0 appears on the switch.
Locking/loosening the die
For straight cuts, tighten the clamping screw (3) using a hex
key (width across flats 2.5 mm) to lock the die (4) in place.
For curved cuts, loosen the clamping screw (3). The die (4)
can move freely now and adjusts to the direction of the feed
strength.
Working Advice
Pull the plug out of the socket before carrying out any
u
work on the power tool.
This power tool is not suitable for bench-mounted use.
u
It must not be clamped into a vice or fastened to a work-
bench, for example.
English | 5
GNA 2,0
0 601 530 1..
W 500
W 270
−1
min 2400
−1
min 1500
mm 2.0
mm 6
mm 3
kg 2.0
/Ⅱ
2
1 609 92A 503 | (31.07.2019)