Télécharger
Partager
Imprimer la page
  1. Manuels
  2. Marques
  3. Whittier Wood Products Manuels
  4. Ameublement d'intérieur
  5. Gourmet 140W
  6. Instructions de montage

Whittier Wood Products Gourmet 140W Instructions De Montage

Masquer les pouces

Publicité

Liens rapides

Télécharger ce manuel
Model #
140W
Gourmet Cart
Assembly Instructions
Congratulations!
This fine piece of furniture will make a handsome
addition to your home. For the best results, start by
reading both the Assembly Instructions and
Finishing Hints before you begin your project.
For normal household use only.
recommended for commercial use.
Do not climb, sit or stand on this piece of
furniture.
Unload items from this unit prior to moving.
Do not overload the drawer on this unit.
P.O. Box 2827
Eugene, OR 97402 USA
Service Policy:
which are defective, missing or damaged
during assembly. Please contact Whittier
Wood Products customer service department
directly (by phone, fax, mail or email) for
replacement parts.
Hours:
Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order:
Provide the complete furniture
model number (upper left corner of this
page), part letter, production code, quantity
needed, reason for replacement and your full
name and address along with a telephone
number in case we need to contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
Outside U.S. or Canada: 541-687-0213
Fax: 541-687-2060 • Email: info@whittierwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Read both the Assembly Instructions and Finishing
Hints completely before beginning.
If you choose to use the top for food preparation, it
should be finished with a non-toxic substance such
as mineral oil or butcher block oil.
Store the parts: 1) in their box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may
be affecting the stability of your furniture. Tighten or
repair as needed.
Production Code:
We will replace any parts
Rev. 5/05

Publicité

loading

Manuels Connexes pour Whittier Wood Products Gourmet 140W

Sommaire des Matières pour Whittier Wood Products Gourmet 140W

  • Page 1 Model # 140W Gourmet Cart Assembly Instructions Service Policy: We will replace any parts which are defective, missing or damaged during assembly. Please contact Whittier Wood Products customer service department directly (by phone, fax, mail or email) for replacement parts. Hours: Our friendly customer service staff can be reached Monday-Friday 7:00 a.m.
  • Page 2 140W Gourmet Cart — Parts List BEFORE BEGINNING ASSEMBLY, check that the quantities of the parts received match those on the parts list below. H — Front/Back Bottom Apron — Qty. 2 A — Right Front Leg — Qty. 1 B —...
  • Page 3 140W Gourmet Cart — Parts List (cont.) V — Slat — Qty. 8 P — Drawer False Front — Qty. 1 Q — Drawer Side — Qty. 2 W — Top — Qty. 1 X — Nickel Towel Bar — R —...
  • Page 4 140W Gourmet Cart — Parts List (cont.) ZN — Drawer Pull — Qty. 1 ZU — Metal Caster ZD — Pad — Qty. 2 Insert — Qty. 4 ZE — 1/2" Cam Connector — Qty. 10 ZV — Shelf Bracket — Qty. 4 ZO —...
  • Page 5 140W Gourmet Cart ASSEMBLY INSTRUCTIONS TOOLS REQUIRED: Phillips Head Screwdriver, Slotted Screwdriver, Wood Glue, Tape Measure, Hammer. IMPORTANT NOTE: We recommend fi nishing the unit before fi nal assembly. Before fi nishing, read enclosed fi nishing hints. Right Front Leg Right Back Leg Top Right Apron Top Back Apron...
  • Page 6 x 12 x 10 FIG. 2 Read the instructions on how to operate CAM-LOCK SYSTEM at this time. 2) Glue 3/8" x 2" Wood Dowels (Z): Insert 1/2" Cam Connectors (ZE): • Six in the Right Front Leg (A), five in the •...
  • Page 7 Cam Housing Holes ZA ZA FIG. 3 3) Lay out the parts as shown in FIGURE 3. Make sure the single 3/8" dowel (Z) in the Right Front Leg (A), the 3/4" Cam Connector (ZK) in the Right Back Leg (B), the three 5mm dowels (ZA) in Bottom Right Apron (E) and the three cam housing holes in the Top Right Apron (C) must all face the same direction, i.e.
  • Page 8 FIG. 5 5) Attach Back Panel (I) to Back Vertical Support (L) with three #6 x 1" Oval Head Screws (ZY) through the predrilled holes in back into back vertical support. Notch in back vertical support is to be flush with bottom edge of back. FIG.
  • Page 9 FIG. 8 8) Start two #8 x 1¼" Black Screws (Y) through the holes in the bottom of the Bottom Shelf (J). Slide the Vertical Divider (M) over the 1/2" Cam Connectors (ZE) and insert 1/2" Cam Housings (ZF) in the holes and tighten. The cam holes in the vertical divider must face toward Left Side Assembly (G).
  • Page 10 FIG. 10 10) Attach Top Back Apron (D) with a 3/4" Cam Housing (ZL). The hole in the middle on one edge must be toward the top. Attach the Sleeper (F) to the left front leg with the dowel (Z). The rounded edges of the sleeper must face the front.
  • Page 11 FIG. 12 12) Attach Right Side Assembly to bottom shelf (J) with dowels (ZA); to lower aprons with 3" Barrel Bolts (ZH) and Barrel Nuts (ZI); to sleeper (F) with dowel (Z); and to top back apron (D) with a 3/4"...
  • Page 12 FIG. 14 14) Lay the Top (W) over the apron/leg assembly so that the cam connectors go through the holes in the top edge of the aprons. Fasten in place with 3/4" and 1/2" Cam Housings (ZL &ZF). See FIGURE 14. FIG.
  • Page 13 FIG. 16 16) Fasten sleeper (F) to the vertical divider (M) with an Angle Bracket (ZM) placed on right side using 1/2" Undercut Screws (ZB). The top edge of the sleeper must be flush with top edge of vertical divider. To ensure proper placement of L-Bracket (ZM) make sure the measurement between the Left Side Assembly (G) and Vertical Divider (M) are equal from top to bottom.
  • Page 14 Side adjustment 4mm (5/32") To move the door towards the side Hinge panel, loosen screw ‘1’ and tighten screw ‘2’. To move the door away from the side panel, loosen screw ‘2’ and tighten screw ‘1’ Depth Adjustment 4mm (5/32") Loosen screw ‘2’...
  • Page 15 FIG. 21 21) Insert the Shelf Brackets (ZV) in the holes at the locations where you want to place the Adjustable Shelf (K). Make sure the wood trim on the edge of the shelf is facing out from the unit. The shelf must be fastened in place with #6 x 1/2"...
  • Page 16 FIG. 24 24) Attach the Drawer Face (S) to the Drawer. Insert the #8 x 1¼" Machine Screws (ZQ) through the center holes in the Drawer False Front and LOOSELY fasten the Drawer Pull (ZN) so that it allows the adjustment of the Drawer Face but holds it in place once moved. See FIGURE 24. DO NOT INSERT THE SCREWS (ZX) AT THIS TIME.
  • Page 17 Modelo # 140W Carro Culinario Normas para obtener servicio: Reemplaza- Instrucciones para Armar remos las piezas que tengan defectos, falten o se dañen durante el armado. Sírvase comunicarse con el departamento de servicio al cliente de Whittier Wood Products directamente (por teléfono, fax, correo o e-mail) para obtener piezas de repuesto.
  • Page 18 140W Carro Culinario Lista de piezas ANTES DE ENSAMBLAR, verifi que que haya recibido todas las piezas que se listan en la lista de piezas que se presenta a continuación. Parte Descripción Cantidad Parte Descripción Cantidad Parte Descripción Cantidad Pata delantera derecha ..1 Soporte derecho de la rejilla.
  • Page 19 140W Carro Culinario Faldón Inferior Derecho (E) y los tres orificios para las parcialmente un Perno Pasante en el orificio en el ensamble tuercas de sujeción de leva que vienen en el Faldón Superior lateral. Coloque una Tuerca Cilíndrica en el orificio del Derecho (C) queden todos mirando hacia la misma dirección, faldón.
  • Page 20 140W Carro Culinario 14. Ponga el Panel Superior (W) sobre el ensamble de faldones/ 19. Fije la perilla (YA) a la Puerta (N) con un Tornillo para patas, de manera que los conectores de leva entren en los Metal #8 x 1" (ZR). Fije los Trozos de Fieltro (ZD) al orificios del borde superior de los faldones.
  • Page 21 No. de modèle 140W Chariot Gourmet Politique de service : Nous remplacerons toutes Instructions de Montage les pièces défectueuses, manquantes ou endom- magées pendant le montage. Veuillez contacter directement le service clientèle de Whittier Wood Products (par téléphone, fax, courrier ou e-mail) pour obtenir les pièces de remplacement.
  • Page 22 140W Chariot Gourmet Nomenclature des pièces AVANT DE COMMENCER LE MONTAGE, assurez-vous que les quantités des pièces reçues correspondent à la nomenclature des pièces fi gurant ci-dessous. PIÈCE DESCRIPTION QTÉ PIÈCE DESCRIPTION QTÉ PIÈCE DESCRIPTION QTÉ Pied avant droit... . . 1 Support droit de claie .
  • Page 23 140W Chariot Gourmet Assurez-vous également que les trois chevilles de 5 mm Fixez le tablier (H) au support vertical arrière (L) au (ZA) dans le tablier inférieur droit (E) sont orientées vers moyen d’une vis à tête ovale no. 6 x 1 po (ZY) que le dessus du tablier.
  • Page 24 140W Chariot Gourmet 20. Fixez le porte-torchon (X) sur le tablier droit au moyen 15. Vous pouvez monter la claie à n’importe quelle hauteur. Faites glisser l’assemblage de la claie jusqu’à la hauteur des vis à usiner no. 8 x 1 po (ZR). Voir la FIGURE 20. désirée.