Electrical Safety Check; Start-Up / Operation; Operation; Stopping - Stiga Park 4WD Serie Manuel D'utilisation

Masquer les pouces Voir aussi pour Park 4WD Serie:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

EN
Exhaust system.
Oil lines
Activate the machine
forwards/backwards
and release the
traction pedal.
Test driving

7 .8 .2 Electrical safety check

Country/State
Driver not seated.
Parking brake
engaged.
Driver seated.
Parking brake
disengaged.
Driver seated.
Parking brake
engaged.
Engine on,
cutting device
disengaged,
parking brake
engaged.
Engine on,
cutting device
disengaged,
parking brake
disengaged.
Engine on, cutting
device engaged,
parking brake
disengaged.
Engine on,
cutting device
disengaged,
parking brake
engaged.
18
No leaks at connections.
All screws tightened.
No leaks. No damage.
The machine will stop.
No abnormal vibrations.
No abnormal sound.
Action
Result
Try to start
The engine
the engine.
does not start.
On the display
(if present)
the message
"SIT DOWN"
appears.
Try to start
The engine
the engine.
does not start.
On the display
(if present)
the message
"PRESS
BRAKE"
appears.
Try to start
The engine
the engine.
starts.
The driver
The engine
gets up
stays on.
from the
seat.
The driver
The engine is
gets up
switched off..
from the
seat.
The driver
The engine is
gets up
switched off..
from the
seat.
The driver
The engine is
gets up
switched off..
from the
seat.
ENGLISH
7 .9

START-UP / OPERATION

When using the machine, the bonnet
must be closed and fastened shut .
Always use full throttle when using the
machine .
1. Open the fuel cock (24:B).
2. Insert the key in the main power switch (12:A).
3. Engage the transmission (19) - (lever out).
4. Insert the key in the switch (14:C).
5. Do not keep your foot on the traction pedal
(13:C).
Cold start
1. Activate the parking brake (13:A).
2. Turn the throttle to full on (14:A).
3. Pull the choke out completely (14:B).
4. Turn the switch key to the "I" position and
press the START button (14:P).
Before starting work with the machine,
wait a few minutes for the oil to warm up .
For use in low temperatures, warm
the machine up to bring the hydraulic
fluid and the transmission to the
proper temperature . Otherwise the
transmission could get damaged .
Warm start
1. Activate the parking brake (13:A).
2. Turn the throttle to full on (14:A).
3. The choke control (14:B) needs to be lowered.
4. Turn the switch key to the "I" position and
press the START button.
To proceed see the instructions provi-
ded in headingparagrafo 7 .9 .1 .

7 .9 .1 Operation

To operate with the machine proceed as described
below:
• Press the pedal (13:A) right down then release it.
• Activate the pedal (13:C) to move the machine.
• Go to the work area.
• If front accessories have been installed, acti-
vate the PTO (14:F).
• Commence work.

7 .10 STOPPING

To stop the machine, proceed as follows:
• Press the parking brake pedal (13:A).
• Pull the lever (13:B) up.
• Release the pedal (13:A).
(Translation of the Original Instructions)

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Pro 740 ioxPro 540 ixPro 340 ixP 901 ph

Table des Matières