Look 796 MONOBLADE RS Notice D'instructions page 158

ES
Nota : Mantener el conjunto de vaina y cables eléctricos por encima y por debajo del ma-
nillar mediante una vuelta de cinta aislante. De esta manera será más fácil fijar el manillar
a la potencia y cerrar la tapa de la potencia sin riesgo de pellizcar los cables eléctricos.
Fig. 6.1
Fig. 6.4
13
Fig. 6.2
Volume (mm3) Masse (g)
GENERAL TOLERANCES :
Dimension from 0 to 15 : ±0.15
Dessiné par
Dimension from 15 to 30 : ±0.20
Beyond : ±0.25
Angles : ±30'
GENERAL TOLERANCES :
Surfaces finish : 80 grit sand blast
Vérifié par
Dimension from 0 to 15 : ±0.15
Volume (mm3)
Free of positive metal, voids and porosity
Dimension from 15 to 30 : ±0.20
Free of cutting oil and oil residue
Beyond : ±0.25
GENERAL TOLERANCES :
Angles : ±30'
Dimension from 0 to 15 : ±0.15 All information contained on this drawing is property of LOOK CYCLE INTERNATIONAL. Its reproduction for any use in any way or for commercial
Dessiné par
Surfaces finish : 80 grit sand blast
Dimension from 15 to 30 : ±0.20 purpose is forbidden. All rights on this material are reserved.
Free of positive metal, voids and porosity
Beyond : ±0.25
Free of cutting oil and oil residue
Angles : ±30'
Surfaces finish : 80 grit sand blast
Vérifié par
Free of positive metal, voids and porosity
Free of cutting oil and oil residue
All information contained on this drawing is property of LOOK CYCLE INTERNATIONAL. Its reproduction for any use in any way or for commercial
purpose is forbidden. All rights on this material are reserved.
GENERAL TOLERANCES :
Dimension from 0 to 15 : ±0.15
Dimension from 15 to 30 : ±0.20
Fig. 6.5
Beyond : ±0.25
Angles : ±30'
GENERAL TOLERANCES :
Surfaces finish : 80 grit sand blast
Dimension from 0 to 15 : ±0.15
Free of positive metal, voids and porosity
Free of cutting oil and oil residue Dimension from 15 to 30 : ±0.20
Beyond : ±0.25
Angles : ±30'
Surfaces finish : 80 grit sand blast
Free of positive metal, voids and porosity
Free of cutting oil and oil residue
Fig. 6.3
Nature de la modification
Matière
Nature de la modification
ECHELLE 1:3
Nature de la modification
FORMAT A3
Matière
Date
ECHELLE 1:3
Volume (mm3) Masse (g)
DESIGNATION
FORMAT A3
Date
ECHELLE 1:3
Masse (g)
Dessiné par Date
FORMAT A3
Date
Vérifié par Date
DESIGNATION
Date
All information contained on this drawing is property of LOOK CYCLE INTERNATIONAL. Its reproduction for any use in any way or for commercial
purpose is forbidden. All rights on this material are reserved.
Volume (mm3) Masse (g)
Dessiné par
Volume (mm3)
Vérifié par
All information contained on this drawing is property of LOOK CYCLE INTERNATIONAL. Its reproduction for any
purpose is forbidden. All rights on this material are reserved.
All information contained on this drawing is property of LOOK CYCLE
purpose is forbidden. All rights on this material are reserved.
Resp Date Ind.
Traitement
Resp
Matière Traitement
ENSEMBLE Resp Date Ind.
Traitement
ENSEMBLE
REFERENCE
ENSEMBLE
DESIGNATION
REFERENCE
Nature de la modification
Matière
Nature de la modification
ECHELLE 1:3
FORMAT A3
Date
ECHELLE 1:3
Masse (g)
DESIGNATION
FORMAT A3
Date
Dessiné par Date
Vérifié par Date
Date Ind.
REFERENCE
R
ENSEMBL