JANE nurse PROTECT Instructions page 21

GB
Press the ISOFIX button to pull out the two locking arms from the bottom of the base. Pull the locking arms
until you hear them click indicating that they are correctly engaged. On both sides of the locking arms the
button will turn green, indicating that they are securely locked.
Pull out the top tether anchor point, press the release button and pull the top tether long enough to hook
onto the safety catch on the back of the vehicle seat.
Hook the safety catch onto the fixed anchor point. The position of the fixed anchor point is shown in the
diagram (one of three positions). Make sure that the hook is held tightly.
5.2.2.2 Groups II, III (15-36KG)
NOTE: When using this safety seat for Groups II and III, remove the 5-point harness, the sleeping pad and
the triangular pad (for further information, please see section 4.7).
Position the child safety seat facing forwards on the vehicle seat (in the direction of travel).
Fit the ISOFIX insertion guides into the two rings of the ISOFIX anchor points of the vehicle.
NOTE: The ISOFIX anchor rings are located between the surface and the backrest of the vehicle seat.
Press the ISOFIX button to pull out the two locking arms from the bottom of the base. Pull the locking arms
until you hear them click indicating that they are correctly engaged. On both sides of the locking arms the
button will turn green, indicating that they are securely locked.
NOTE: When using this safety seat for Groups II and III, remove the 5-point harness, the sleeping pad and
the triangular pad (for further information, please see section 4.7). Position the child safety seat facing
forwards on the vehicle seat (in the direction of travel).
Step 1: Firstly, take the belt out of the ALR (automatic locking retractor), the diagonal belt through the belt
guide (1) and the lap belt through the belt guide. Then, place them together through the belt guide (3).
NOTE: Check that the diagonal section of the seat belt is positioned above the child's shoulders, and not
across his neck.
Step 2: Insert the protruding metal part of the seat belt into the buckle until you hear it click into place.
Follow the direction of the arrow to tighten the belt and put the surplus belt under the fabric cover.
Gently move the safety seat to check it is held securely in place.
WARNING: The diagonal section of the seat belt should go diagonally backwards. You can adjust the
position of the seat belt with the seat belt adjuster on both sides.
6
6. CARE AND MAINTENANCE
Regularly inspect the safety seat to check for worn or damaged parts. If any of the parts are damaged,
replace the safety seat. Keep the seat clean. Do not lubricate any parts of the safety seat.
To prolong the life of this product, keep it clean and do not expose it to direct sunlight for prolonged
periods of time.
The fabric covers and other removable parts can be cleaned using warm water with soap or mild detergent.
Allow it to dry fully, preferably out of direct sunlight.
CLEANING THE HARNESS BUCKLE
Remains of food, drink and other substances can build up on the harness buckle which can affect its
functioning.
Wash it with warm water until it is fully clean. Make sure you can hear an audible click to make sure the
buckle is working properly.
CLEANING THE HARNESS AND THE SHELL
Sponge clean with soap and warm water. Do not use any other cleaning agents.
STORING THE SAFETY SEAT
Store in a safe, dry place, away from heat and direct sunlight. Avoid placing heavy objects on top of the seat.
30ºC
Wash at or
Do not
below
bleach
7 7. WARRANTY
The warranty period starts on the date of purchase and is valid for a period of 24 months. The warranty
is only applicable to material and production defects. The date of purchase can only be proven with the
original sales receipt. This warranty is only applicable to the original owner and is not transferable. The
warranty is only applicable to products that have not been altered by the user in any way. In the case of
any defects, the owner is required to return the product to the retailer.
The manufacturer is not responsible for any damages other than those to products supplied or
manufactured.
8
8. MAIN TECHNICAL PARAMETERS
Length: 510mm
Width: 440mm
Height: 600-800mm
Do not dry
Do not
clean
iron
Do not Dry flat in
tumble dry shade
21