Publicité
Les langues disponibles
Les langues disponibles
Trimmer/Brushcutter-17 lgs
GB
F
D
E
ASSEMBLY
ATTACHING THE SHOULDER STRAP (Fig. 5)
1. Connect the latch (33) on the shoulder strap to the
strap hanger.
2. Adjust the strap to a comfortable position.
NOTE: To quickly release the product from the shoulder
strap, sharply pull the quick release tab (32).
SILENCER GUARD ASSEMBLY (Fig. 6)
1. Remove silencer guard and two screws from the
owner's kit.
2. Attach the silencer guard to the rear housing (35).
NOTE: Make sure the bent end of the silencer guard (39)
fits securely into the opening of the rear housing (40).
3. Install two screws.
4. Tighten screws securely.
GRASS DEFLECTOR AND BLADE GUARD USE
(Fig. 7)
NOTE: When converting from brushcutter to trimmer, or
trimmer to brushcutter, make sure the correct guard/
deflector is being used.
a. for Trimmer
b. for Brushcutter
BLADE GUARD (Fig. 8)
1. Attach the blade guard to the mounting bracket (41);
install the four screws (10-24 x 3/4 in) from the top of
the mounting bracket through the blade guard and into
the threaded mounting plates (44).
2. Using the torque wrench supplied, tighten all four
screws securely.
NOTE: When using the string head (48), the string shield
must be attached to blade guard.
GRASS DEFLECTOR (Fig. 8)
1. Attach the grass deflector to the blade guard by
placing the three locking tabs (43) into the three
notches (42).
2. Snap the blade guard and grass deflector together to
lock into place.
WARNING
Always stop the engine and remove the sparking
plug wire before making any adjustments such
as changing cutting heads; this is to reduce the
risk of serious personal injury.
30/09/03
17:00
I
P
NL
S
DK
English
CONVERTING
BRUSHCUTTER
REMOVING THE STRING HEAD (Fig. 9)
1. Align the slot in the upper flange washer (50) with the
2. Place the holding pin through the upper flange washer
3. Remove the upper flange washer from the gear shaft
4. Remove the grass deflector by pushing in on the three
NOTE: Store the string head parts together for later use.
INSTALLING THE BLADE (Fig. 10)
1. Place the upper flange washer over the gear shaft with
2. Centre the blade on the upper flange, making sure the
3. Place the holding pin through the slot in the upper
4. Tighten nut securely.
CONVERTING FROM BRUSHCUTTER TO
TRIMMER
REMOVING THE BLADE (Fig. 10)
1. Place the holding pin through the slot in the upper
2. Remove the cupped washer and the blade.
3. Remove the upper flange washer from the gear shaft
4. Attach the grass deflector to the blade guard by
5. Snap the blade guard and grass deflector together to
NOTE: Store the brushcutter parts together for later use.
16
Page 16
N
FIN
GR
H
CZ
FROM
hole in the gear head. Place the holding pin through the
slot in the upper flange washer and the hole in the gear
head. Turn the spool retainer (47) clockwise to remove.
Remove the spool and string head from the
drive connector (46).
and the gear head. Using the 16 mm (5/8 in) spanner
(45) supplied, turn the drive connector clockwise to
remove.
and retain for blade installation.
locking tabs while pulling on the grass deflector to
separate from the blade guard.
the hollow side towards the blade guard.
blade sits flat. Install the cupped washer (53) with
the raised centre away from the blade. Install the blade
nut (52). The blade turns anticlockwise from the
operator's position.
flange washer and the hole in the gear head. Using the
13 mm (1/2 in) (51) spanner supplied, turn the blade
nut anticlockwise.
flange washer and the gear head. Turn the blade nut
clockwise to remove.
and retain for the string head installation.
placing the three locking tabs into the three notches.
lock into place.
RUS
RO
PL
TRIMMER
TO
Publicité
