Publicité
Les langues disponibles
Les langues disponibles
• Before powered on, the switch must be confirmed
in "off" position; before you put down the power tool, it
must be turned off and the power plug must be pulled
out�
• When the accessory is totally static, then the power
tool can be put down�
• Chiseling walls, floors or on similar occasions, pay
attention to keep away from gas, tap water pipeline
and electric wire and operating tools in those places
shall keep away from touching metal parts� The appro-
priate detector shall be used so as to find out the loca-
tion of the concealed power wire� Or you can require
the relevant data from the local power supply entity�
The wires that are drilled through shall result in the fire
and electric shock� The damaged gas pipe will resulted
in the explosion� If the water pipe is drilled through, the
property loss will be caused�
• If the accessory installed on the power tool gets
clamped, the power tool must be turned off immedi-
ately and stay calm� At the time, the power tool will
generate ultra-high reaction torque, and result in the
return stroke� The accessory installed on the power
tool is easy to be clamped, like: the power tool is in
hypercharge, or the accessory installed on the power
tool inclines in the workpiece�
• Two handles of the productor must be held with both
hands tightly in operation, and the base must be sta-
ble� Both hands can hold the power tool stably; one
hand operation must be avoided�
• The flat chisel must not be used in the rotational
state (such as rotary drill and hammer drill), or the chis-
el will be blocked and the power tool will lose control�
• Only when you wear gloves then you can touch the
accessories, the drill bits and accessories will be hot
in operation, and it is easy to get burn� Never imme-
diately touch the drill bit or parts around it upon the
end of work, for those parts will be scalding and scald
your skin� Wear gloves and middle rest can reduce the
vibration and the injury to the hands and arms�
• Hands and body must not be placed between the
power tool and the wall or column so as to prevent the
power tool from flying off when the drill bits gets blocked.
• Avoid stopping an power tool motor when loaded�
• Never remove any chips or fragments with your
power tool's motor running�
• Never change the borer and chisel design or use
attachments and appliances, which are not recom-
mended for your power tool�
• When working, never press the power tool too hard,
as this might lead to the borer or chisel seizing and
motor overloading�
• Avoid the drill, borer and chisel seizing in the materi-
al worked in� If this happens, do not try to release them
with your perforator's motor� It may damage the motor�
• Never force out the drills, borers or chisels stuck
in the material you are working on with a hammer or
other objects the chipped off metal particles may harm
both the operator and the persons who are nearby�
• Avoid overheating your power tool, when using it for
a long time�
Warning: the chemical substances con-
tained in dust generated in sanding, cut-
ting, sawing, grinding, drilling and other
construction industry activities may
result in cancer, congenital deficiency or be harm-
ful to the fertility. The ion of some chemical substanc-
es shall be:
• before any repair and replacement work to the
machine, the power plug must be pulled out firstly;
• the transparent two silicon oxide and other ma-
sonry products in the wall bricks and cement; the
chromium arsenic (CCA) in wood with chemical
treatment� The harm degree of these substances
shall depend on the frequent degree of you carrying
out these works� If you want to reduce the contact
with these chemical substances, please work in the
place with ventilation and you shall use the appli-
ances with safety certificates (such as the dust mask
designed with tiny dust filter).
Following symbols are used in the operation manual,
please remember their meanings� Correct interpreta-
tion of the symbols will allow correct and safe use of
the power tool�
Symbol
English
25
Symbols used in
the manual
Meaning
Cordless rotary hammer
Sections marked gray - soft
grip (with insulated surface)�
Serial number sticker:
ABH- ��� - model;
XX - date of manufacture;
XXXXXXX - serial number�
SDS PLUS (chuck or acces-
sory shank type)�
Brushless motor�
Read all safety regulations
and instructions�
Wear safety goggles�
Wear ear protectors�
Wear a dust mask�
Publicité
