Checchi & Magli UNIFOX Manuel D'utilisation Et D'entretien page 60

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

Adjusting the plant spacing
The distance between one seedling and the next is de-
termined by the number of teeth of the pinions installed
and the number of grippers fitted to the dispenser.
A series of pinions may be fitted to ensure the required
plant spacing is obtained.
The pinions must be replaced on all the planting units
fitted.
The charts state the possible distances - in relation to the
grippers fitted on the dispenser - between one seedling
and the next according to the available pinion range.
To mount the pinions, see the section on "Replace the
driving wheel pinions" on page 32.
Set - up of the dispenser fitted with a single gripper
Plant spacing distance
cm
inches
700
275-5/8"
640
252"
600
236-1/4"
570
224-3/8"
540
212-5/8"
500
196-7/8"
475
187"
440
173-1/4"
420
165-3/8"
380
149-5/8"
350
137-3/4"
320
126"
Set - up of the dispenser fitted with 5 grippers
Plant spacing distance
cm
inches
140
55-1/8"
128
50-3/8"
120
47-1/4"
114
44-7/8"
108
42-1/2"
100
39-3/8"
95
37-3/8"
88
34-5/8"
84
33-1/8"
76
30"
70
27-1/2"
64
25-3/16"
(z) = N. teeth on the pinion
English language
ADJUSTMENT INFORMATION
A
B
C
D
(z)
(z)
(z)
(z)
12
20
16
16
15
23
16
16
14
20
16
16
14
19
16
16
17
22
16
16
19
23
16
16
20
23
16
16
19
20
16
16
20
20
16
16
22
20
16
16
23
19
16
16
21
16
16
16
A
B
C
D
(z)
(z)
(z)
(z)
14
23
16
16
15
23
16
16
16
23
16
16
16
22
16
16
17
22
16
16
15
18
16
16
17
19
16
16
21
22
16
16
21
21
16
16
22
20
16
16
23
19
16
16
21
16
16
16
Dispenser
Driving wheel
UN41 0588GN ing
Set - up of the dispenser fitted with 2 grippers
Plant spacing distance
cm
inches
350
137-3/4"
320
126"
300
118-1/8"
285
112-1/4"
270
106-1/4"
250
98-1/2"
240
94-1/2"
220
86-5/8"
210
82-3/4"
190
74-7/8"
175
68-7/8"
160
63"
Set - up of the dispenser fitted with 10 grippers
Plant spacing distance
cm
inches
78
30-3/4"
69
27-1/8"
62
24-3/8"
55
21-5/8"
49
19-5/16"
43
17"
39
15-5/16"
35
13-3/4"
31
12-3/8"
27
10-5/8"
23
9-1/16"
---
---
(z) = N. teeth on the pinion
20
5
A
B
C
D
(z)
(z)
(z)
(z)
12
20
16
16
15
23
16
16
16
23
16
16
17
23
16
16
17
22
16
16
19
23
16
16
19
22
16
16
20
21
16
16
21
21
16
16
21
19
16
16
19
16
16
16
21
16
16
16
A
B
C
D
(z)
(z)
(z)
(z)
12
22
16
16
14
23
16
16
15
22
16
16
17
22
16
16
19
22
16
16
21
21
16
16
22
20
16
16
23
19
16
16
23
17
16
16
22
14
16
16
22
12
16
16
---
---
---
---
Use and maintenance

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

Unifox dt

Table des Matières