Troubleshooting; Specifications - Teac DV-M5000 Manuel Du Propriétaire

In case of any trouble with this unit, please take the time to look through this chart and see if
you can solve the problem yourself before you call your dealer or a TEAC service center.
No power
e Check the connection to the AC wall outlet.
Play does not start
eReload the disc with the label side UP.
eClean the disc.
Hand mark on screen
eThe selected function does not operate for that disc or another operation is still in
process. Wait a moment and try again.
Picture playback stops and operation buttons will not work.
eFirst, stop the disc (press the STOP button), then start playback again.
eTurn the unit off and back on again and restart the playback.
No picture.
eCheck that the system is connected properly.
eMake sure you have selected the proper video input on the TV.
Picture noise.
eIf video from this system has to go through your VCR to get to your TV, the copy-
protection applied to some DVD programs could affect picture quality. Please connect
the unit directly to your TV.
There is no sound or only a very low-level sound is heard.
eCheck that the speakers and components are connected securely.
eMake sure the MUTE button has not been pressed or activitated.
eMake sure that you have selected the correct source on the system.
eMake sure the unit is not in the pause mode or in slow-motion play mode, or fast
forward or fast reverse. Press the PLAY(G )button to return to normal play mode.
Severe hum or noise is heard.
eCheck that the speakers and components are connected securely.
Remote control doesn't work.
eIf the batteries are dead, change the batteries.
eUse remote control unit within the range (5m/15ft) and point at the front panel.
eClear obstacles between the remote control unit and the main unit.
eIf a strong light is near the unit, turn it off.
Cannot play.
eLoad a disc with label side up.
eIf the disc is dirty, clean the surface of the disc.
eA blank disc has been loaded. Load a prerecorded disc.
Sound skips.
ePlace the unit on a stable place to avoid vibration and shock.
eIf the disc is dirty, clean the surface of the disc.
eDon't use scratched, damaged or warped discs.
If normal operation cannot be recovered, unplug the power cord from the outlet and plug it
in again. This resets the internal micro-computer which can be disturbed during electrical
storms, power interruptions, et cetera.
26

Troubleshooting

ENGLISH

Specifications

System: 5-disc DVD/VCD/MP-3/CD/CD-
R/CD-RW Changer
Frequency response: 20 - 18 kHz
Harmonic distortion: Less than 0.02%(1kHz)
S/N ratio (IHF-A): More than 98 dB
Channel separation: 8 5 dB
Laser pickup (wavelength):
DVD: 640 ~ 660 nm
CD: 760 ~ 800 nm
Laser power: CLASS II
Error correction: CIRC
Digital filter: 8 times over sampling
D/A converter: 64fs Dual Delta Sigma
converter
Output:
Video output: 1 - Pin (RCA) jack
S-Video output: 1 - S terminal
Component video output:
1 - Pin (RCA) jack
Digital output:
Optical 1 - Optical (TOS) terminal
Coaxial 1 - Pin (RCA) jack
Power Source: AC 100 - 240V, 50/60 Hz
Power consumption: 15 watts
Dimensions (WxHxD): 435 x 124 x 382 mm
Weight: 6.2 Kg (13-5/8 lbs)
Supplied accessories:
RCA cable (for audio) x 1
RCA video cable x 1
Remote control unit x 1
< Improvements may result in changes in
the specifications and features.
< Illustrations may differ slightly from the
production model.