How To Pair Two Btx1 Pro Units; Set Up Of The Agc System; Compatibility With Midland Bt Line Units; Talk 2 All - Universal Intercom With Different Brand Unit - Midland BTX1 PRO Guide D'utilisation

How to pair two BTX1 PRO units

The two units supplied in the same BTX1 PRO box, are already paired and ready to use,
which means you don't need to perform this procedure. The units are already paired using
the Middle button.
If the devices are not part of the same kit, or the units have been purchased separately,
you need to first pair it in order to use it.
To pair the BTX1 PRO to another BTX1 PRO unit
To pair the BTX1 PRO to another BTX1 PRO unit, you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the middle button about 7 sec., until the Red light is on perma-
nently.
3. Now press the Middle button for 3 seconds. The Blue and Red light will flash.
4. Do the same procedure on the other unit, When successfully paired, each unit will
have the Blue light on for one second and then go back to the setup mode (Red light
always on).
5. Now the pairing procedure is complete, you just need to exit the setup mode before
you can use the units:
6. Double click on the Middle button, the Red light will turn off and the Blue light will
start flashing. You can use now your BTX1 PRO.
How to use the Intercom
To use the intercom feature, be sure that both units are turned on and correctly paired
together.
Manual activation
Press the Middle button on one of the two units in "Intercom" mode. Communication is
enabled and remains active until you press again the middle button. The intercom need
some second to activate, you will hear a beep tone when the intercom is open.
Voice activation (VOX)
Simply say something, after some seconds the communication will be opened and will
remain active for the time you are talking. If there is no conversation the intercom will be
closed after 40 seconds. If needed you can close the intercom manually without waiting
40 seconds (just press the middle button).
20
If needed, you can disable the VOX feature simply by pressing the Backward button for
7 sec. A voice announcement will advise you when the VOX is disabled. To turn the VOX
on again, just press the same button and a voice announcement will advise you that the
VOX is now active. This setting is remembered also if you turn off the unit.
Adjusting the volume
Your Midland BTX1 PRO uses AGC technology, which automatically adjusts the listening
volume in relation to background noises. However, it is also possible to manually adjust
the volume by means of the "Volume +" and "Volume -"buttons.
The volume setting is indipendent for each audio source: intercom, stereo music, phone
call, FM radio.
Attention: volume can be adjusted only when an audio connection is active.

Set up of the AGC system

To adjust the sensitivity of the AGC system you can use the "BT UPDATER" Pc Softwa-
re or the smartphone "BT SET-APP" application. You can choose different set up based
on your motorbike type (naked, touring, sport) or if you are riding as a passenger. You can
disable the AGC system pressing "Volume +" and "Volume -" togheter for 3 sec.

Compatibility with Midland BT line units

The BTX1 PRO is compatible with BTX2 PRO, BT Next PRO, BT Next Conference,
BTX2 FM and BTX1 FM.
When paired the max distance of the intercom is defined from the lower possible.
The BTX1 PRO is compatible with the previous line of Midland BT (BT Next, BTX2 and
BTX1) only if updated to firmware version 2014 or later.

Talk 2 All - Universal Intercom with different brand unit

Thanks to the "Talk2 All - Universal Intercom" feature it is now possible to pair your BTX1
PRO to a different brand intercom available on the market.
1. On the BTX1 PRO enter the setup mode: (With the unit OFF press and hold down the
Middle button about 7 sec., until the Red light is on permanently.
2. Press the "Forward" button for 3 seconds, the Red and Blu LED light will flash slowly.
3. On the other intercom (not Midland brand) follow the procedure to pair to a phone.
www.midlandeurope.com