Switching On And Off Your Midland Btx1 Pro; Operative "Mode; How To Pair Two Btx1 Pro Units - Midland BTX1 PRO Guide D'utilisation

Boom Microphone
Place the section with the Velcro/adhesive strip between the padding and the rigid cover
of the helmet, so that the microphone is correctly positioned in front of your mouth and
that the white symbol is facing your mouth. This type of microphone is suited for Open
Faced and Flip Front helmets.
Wired microphone
Using the Velcro/adhesive strip, place the microphone inside the helmet in front of your
mouth. This type of microphone is more suited for Full Faced helmets. The mini con-
nector on the microphone allows you choose the microphone that best suits the helmet
you are using.
Description of the Slide-in mounting kit
To fix the Midland BTX1 PRO onto the helmet, you have to install the slide-in mounting
kit by using the plate with bi-adhesive strip. This method allows you to safely "fix" the
BTX1 PRO unit onto your helmet and to remove it at any time in order to recharge or
store it.
4
Plate with bi-adhesive strip
The Bi-adhesive plate is already assembled on the slide-in mounting kit.
Bi-adhesive
Clean the application area on the helmet surface, remove the bi-adhesive film and place
the fixing plate on the left side of the helmet by keeping it contact with the surface for
a few seconds.
Fitting and removing your Midland BTX1 PRO
The BTX1 PRO can be easily fitted onto the helmet by sliding it downwards on the sliding
mounting kit. BTX1 PRO is maintained in position thanks to the fixing clip located on the
upper section (A). To detach the BTX1 PRO, simply press the fixing clip and push the
unit upwards.
Lock Unlock
A
www.midlandeurope.com

Switching ON and OFF your Midland BTX1 PRO

Switching the unit on:
Press and hold "Middle" button for approximately 3 seconds until the BLUE indicator
lights.
Switching the unit off:
Press and hold both "Middle" and "Backward" buttons together for approximately 3 se-
conds until the RED indicator flashes 3 times, thus lessening the chances that you might
turn off the unit accidentally (especially whilst wearing gloves).

Operative "mode"

The BTX1 PRO can operate in three main "mode": Intercom, Phone and FM Radio.
The 3 multi function buttons can have different functionality depending on which mode
the unit is at that moment.
› In "Intercom mode" the three buttons let you manage the Intercom communications
between driver and passenger or bike to bike.
› In "Phone mode" you can manage your Bluetooth mobile phone to place/answer a
phone call or to listen to the music or GPS App. announcement (in stereo mode).
Please use your phone responsibly and safely.
› In "FM Radio mode" you can listen to your favourite radio station in stereo, seek for a
specific radio station and save it (6 memories are available).
You can switch (toggle) from one mode to the other simply pressing the Middle button
for 3 seconds. A voice announcement will tell in which mode you are on.
The toggle sequence is the following:
› Intercom mode (if another unit has been paired)
› FM Radio
› Phone mode (if a phone has been paired)
Every time you turn on the unit, the default mode is the last used mode.
The Intercom mode and Phone mode are avalaible only if it was previously paired to
another unit or to a phone.
If you need to know in which mode the unit currently is, just press the "Volume + " and
"Volume –" button together. A voice announcement will tell you the current mode.
www.midlandeurope.com

How to pair two BTX1 PRO units

The two units supplied in the same BTX1 PRO box, are already paired and ready to use,
which means you don't need to perform this procedure. The units are already paired using
the Middle button.
If the devices are not part of the same kit, or the units have been purchased separately,
you need to first pair it in order to use it.
To pair the BTX1 PRO to another BTX1 PRO unit
To pair the BTX1 PRO to another BTX1 PRO unit, you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the middle button about 7 sec., until the Red light is on perma-
nently.
3. Now press the Middle button for 3 seconds. The Blue and Red light will flash.
4. Do the same procedure on the other unit, When successfully paired, each unit will
have the Blue light on for one second and then go back to the setup mode (Red light
always on).
5. Now the pairing procedure is complete, you just need to exit the setup mode before
you can use the units:
6. Double click on the Middle button, the Red light will turn off and the Blue light will
start flashing. You can use now your BTX1 PRO.
How to use the Intercom
To use the intercom feature, be sure that both units are turned on and correctly paired
together.
Manual activation
Press the Middle button on one of the two units in "Intercom" mode. Communication is
enabled and remains active until you press again the middle button. The intercom need
some second to activate, you will hear a beep tone when the intercom is open.
Voice activation (VOX)
Simply say something, after some seconds the communication will be opened and will
remain active for the time you are talking. If there is no conversation the intercom will be
closed after 40 seconds. If needed you can close the intercom manually without waiting
40 seconds (just press the middle button).
5