Setup And Special Configurations; Setup And Firmware Update - Midland BTX1 PRO Guide D'utilisation

FM Radio with intercom
When you are in "FM Radio" mode is not possible to manually open the intercom, you
can only open it using VOX feature (just talk) to the unit paired on the "Middle" button.
To manually activate the intercom you must switch to "Intercom" mode.
How to Disable/Enable the FM Radio
By default the FM radio is on.
Disabling:
› Enter the "Setup" mode: turn off the unit and hold down the "Middle" button about 7
sec., until the Red light is on permanently.
› Press "Middle" and "Volume+" buttons together for 3 seconds. The blue LED will flash
three times.
› Double click on the "Middle" button to exit the "Setup" mode and use the BTX1 PRO.
Enabling:
› Follow the same procedure up described; now the blue LED will flash once.
› To exit the "Setup" mode, double click the "Middle" button.
Pairing to a PMR446 radio with integrated or external Bluetooth
The PMR446 Radio can be paired to the "Volume +" or "Volume -" button. If paired on
"Volume -" and the "Background" feature is activated, the PMR446 radio is always in the
background even when you talk on the intercom.
Pairing procedure
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
manently.
› Now press firmly (3 sec) the "Vol +" or "Vol -" button, the Blue and Red light will flash.
Radio FM mode
Mode Forward button
FM Radio Short press: seek station up
Long press: Scan recorded
10
› Follow now the pairing procedure explained on the manual of the transceiver itself.

Setup and special configurations

Resetting all paired devices
Sometimes you may find it necessary to delete all the pairing references stored in the
BTX1 PRO unit (reset operation).
To perform this operation you must first enter the setup mode:
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
manently.
› Then simultaneously press and hold down the "Volume +" and "Volume –" buttons for
3 seconds. The Blue Light will be lit on for 1 sec and then back to steady RED.
› Double click on the "Middle" button to exit the "Setup" mode and use the BTX1 PRO.
This procedure deletes all the paired Bluetooth devices stored in the memory therefore
you will not have "Phone" and "Intercom" mode, only "FM Radio" mode will be available.
Back to factory setting
Sometimes you may find it necessary to go back to the factory setting, to reset all the
changes/setup already made and have a "clean" unit.
To perform this operation you must first enter the setup mode:
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
manently.
› Then simultaneously press and hold down all the three buttons "Forward"-"Midd-
le"-"Backward" for 3 seconds. The Blue Light will be lit on for 1 sec and than back to
steady RED.
› Double click on the "Middle" button to exit the "Setup" mode and use the BTX1 PRO.
Middle button Backward button
Short press: On/off Short press: seek station down
Long press: Change mode Long press: Scan recorded
www.midlandeurope.com
This procedure deletes all the paired Bluetooth devices stored in the memory therefore
you will not have "Phone" and "Intercom" mode, only "FM Radio" mode will be available.
Adjusting/ Disabling the VOX feature (Intercom and telephone)
The Intercom feature can be enabled both manually and vocally (VOX). The VOX activa-
tion is influenced by the background noise and therefore by the speed and wind.
For optimum results, it is possible to choose one of the following four microphone sen-
sitivity levels: high, medium, low and very low. The default setting of BTX1 PRO is "me-
dium". It is also possible to disable the VOX feature in order to activate the Intercom and
phone call answering features in manual mode only.
Adjusting the sensitivity of the microphone (VOX)
To perform this operation you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
manently.
3. Your BTX1 PRO is now in "Set up mode".
4. Press shortly the "Backward" button, the red light indicator changes to a steady blue.
5. Now, press "Volume +" or "Volume -" to increase or reduce sensitivity. Every time you
press the Volume buttons the RED light will flash for confirmation. When you reach
the end of the upper and lower limit, the RED light will not flash.
6. Press again the "Backward" button; the Blue light will flash several times, in order to
let you know the selected sensitivity:
One flash = VOX disabled
Twice = low sensitivity
3 times= normal sensitivity
4 times= high sensitivity (default setting)
5 times = highest sensitivity
The light indicator is back to RED ("Set up mode") and the changes are confirmed.
7. If needed, you can adjust again the sensitivity repeating the steps from point 1,
otherwise exit the Setting mode by double clicking the "Middle" button. Once the red
light turns off, the blue led starts blinking. Now you can use your BTX1 PRO.
www.midlandeurope.com
Disabling the VOX feature (Intercom and telephone)
Follow all the procedure described in the previous steps and choose the option of only
one flash (VOX disabled).
Wired connection always in background
This feature let you keep the wired connection always on, even when the phone or the
intercom is open (but not when you are in FM radio mode).
By default the Background feature is ON.
Disabling:
› Enter the "Setup" mode:
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
manently.
› Press the "Forward" and "Middle" button together for 3 seconds. The blue LED will
flash three times.
› Double click on the "Middle" button to exit the "Setup" mode and use the BTX1 PRO.
Enabling:
Follow the same procedure up described; now the blue LED will flash once.
To exit the "Setup" mode, double click the "Middle" button.

Setup and Firmware update

It is possible to configure and update the firmware of your BTX1 PRO using the USB
connection to your PC. On the Midland web site www.midlandeurope.com in the BTX1
PRO page you can find the PC software and the new firmware updates if available.
ATTENTION DO NOT CONNNECT THE UNIT TO THE PC BEFORE you DOWNLOAD
AND INSTALL THE SOFTWARE
11