Features Of The Amplifier And Control Sections - dB Technologies Sigma S218 Caractéristiques Techniques

English

FEATURES OF THE AMPLIFIER AND CONTROL SECTIONS

DIGIPRO G3 amplifier is at the heart of SIGMA S218.
The system is silent and is controlled by a dedicated
DSP that manages the different parameters.
The sound amplification power is 1800 W RMS.
The amplifier panel is made up of:
• Input, Output and Control Section
• Power Supply Unit Section
WARNING
• Never attempt to disassemble the amplifier
in any way.
• In case of overheating, the audio volume
is gradually reduced until module thermal
stabilization. The level is automatically
restored when the correct operating
temperature is reached.
• In the event of a malfunction, immediately
cut power supply off, by disconnecting the
module from the mains, and contact an
authorised repair centre.
• The fuse installed at the factory is rated for
operation in the 220-240 V voltage range. If
you need to operate the speaker in the 100-
120V~ range:
1. Disconnect all connections,
including the power supply
connection.
2. Wait 5 minutes.
3. Replace the fuse with the fuse
rated for the 100-120 V range,
which is included in the package.
WARNING
• Never remove the front grille protecting
the product. To prevent electric shock,
in case of protection grille accidental
damage or replacement (to be carried out
at the after-sales service), immediately
disconnect power supply. Never connect
mains power supply when the grille is
removed.
SIGMA S218
!
!
BALANCED
OUTPUTS
OUT 1 OUT 2
XOVER
OUTPUTS
MODE
BALANCED
INPUTS
INPUT 1 INPUT 2
DELAY POLARITY SUBWOOFER
0
4.5 [ms]
0.5 LEVEL
4.0
1.0
SUBWOOFER
SETUP
3.5 1.5
3.0 2.0 0°
2.5
180°
BALANCED
OUTPUTS
OUT 1 OUT 2
120Hz
XOVER 90Hz
OUTPUTS
MODE Xover Link
BALANCED LIMITER
INPUTS
SIGNAL
MUTE/PROT
READY
SERVICE
INPUT 1 INPUT 2 DATA
DELAY POLARITY SUBWOOFER
4.5 0 0.5 [ms] LEVEL
4.0
SUBWOOFER 1.0 STEREO 0dB
SETUP 3.5 1.5
3.0 2.0 0°
2.5 180° 0dB
MONO
TECHNOLOGIES
DESIGNED & DEVELOPED
IN ITALY
This device complies with part 15 of the FCC Rules. "CAUTION"
(1) This device may not cause harmful interference, Operation is subject to the following two conditions: RISK OF ELECTRICAL SHOCK
and (2) this device must accept any interference DO NOT OPEN
undesired operation. received, including interference that may cause RISQUE DE CHOCH ELECTRIQUE "ATTENTION"
MAINS FUSES AUTO-RANGE MAINS LINK NE PAS OUVRIR Made in China
MAINS INPUT
220-240V~ (T4A L 250V~)
100-120V~ (T8A L 250V~)
220-240V~ 50-60Hz 6A 220-240V~ (10Amax) 2300Wmax
AEB INDUSTRIALE S.R.L. (REMPLACER LE FUSIBLE AVEC LE MÊME TYPE) (REPLACE FUSE WITH SAME RATINGS) 100-120V~ 50-60Hz 12A 100-120V~ (3Amax) 330Wmax
Località Crespellano Via Brodolini, 8
40053 VALSAMOGGIA (BO)
ITALY
MAINS FUSES AUTO-RANGE MAINS LINK
MAINS INPUT
220-240V~ (T4A L 250V~)
100-120V~ (T8A L 250V~)
220-240V~ 50-60Hz 6A 220-240V~ (10Amax) 2300Wmax
(REPLACE FUSE WITH SAME RATINGS)
100-120V~ 50-60Hz 12A 100-120V~ (3Amax) 330Wmax
(REMPLACER LE FUSIBLE AVEC LE MÊME TYPE)
Cod. 420120258 REV. 1.0
120Hz
90Hz
Link
Xover
LIMITER
SIGNAL
MUTE/PROT
READY
SERVICE
DATA
0dB
STEREO
0dB
MONO
23