Publicité
USA
MATERIAL JAM IN THE MACHINE:
(Auto reverse function)
If a jam is caused by too much material being fed
in the following happens:
- The cutters jam, then run in reverse for a short
time (material is released) and stop. The motor
switches off. The control display
on.
Proceed as follows:
Paper jam in paper feed slot (11)
- Remove the paper that has been fed back.
- The cutters now run forwards automatically
and shred the remaining paper in the cutters.
During the forward run the forward button (3)
LED display
comes on. The control display
(6) goes out.
- Continue shredding with less paper.
- If necessary, switch the cutters manually
alternately from forward to reverse until the
material has gone through completely and
been shredded.
Before starting any repair work and
also before cleaning/maintenance
which
is
not
the
following
section
disconnect
the
supply!
CLEANING THE PHOTOCELLS:
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier.
To remove these paper strips and also to clean
the photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both "eyes" of the photocell with a brush.
Model
Typ
intimus 120SP2(SC2)
227-6S
intimus 120SP2(SC2)
227-4S
intimus 120CP4(CC3)
227-4C
intimus 120CP5(CC4)
227-2C
intimus 120CP6(CC5)
227-1C
intimus 120CP7(CC6)
227-1CF
Listed Circuit Breaker:
220-230V = 10 amps / 120V = 15 amps / 100V = 18 amps
Model
intimus 120SP2(SC2)
220-230V/50Hz · 7.8 amps · 1.8 kW
intimus 120SP2(SC2)
220-230V/50Hz · 7.8 amps · 1.8 kW
intimus 120CP4(CC3)
220-230V/50Hz · 7.8 amps · 1.8 kW
intimus 120CP5(CC4)
220-230V/50Hz · 7.8 amps · 1.8 kW
intimus 120CP6(CC5)
220-230V/50Hz · 7.8 amps · 1.8 kW
intimus 120CP7(CC6)
220-230V/50Hz · 7.8 amps · 1.8 kW
LIGHT BARRIER COVERED
WHEN DOOR OPENED:
Should there still be material in the feed slot
when the door is opened, the motor switches off
and the cutters stop. The control display
comes on.
(6) comes
Close the door and acknowledge the status
by pressing the forward button (3) briefly.
The existing material is fed to the cutters and
shredded.
LIGHT BARRIER COVERED
WHEN MACHINE TURNED ON:
Should there still be material in the feed slot
when the machine is switched on the control
display
Remove the material and acknowledge the
status by pressing the forward button (3) briefly.
MOTOR PROTECTION:
Should the motor be overloaded it switches off.
The machine can be started again after a cooling
down period of about 25 – 40 minutes.
MAINTENANCE / DISPOSING
CUTTER MAINTENANCE (CROSS CUT):
Cross cut cutters must be oiled after a
specific operating time. If the control
described
in
display
always
Open the door. The control display
mains
power
and the reverse button (4) LED display
as the control display
oil reservoir (14) (Fig. 4) from the holder in the door
and close the door again.
Pour a little oil onto a sheet of paper and then
feed this through the paper feed slot (11) onto the
cutters.
The paper is drawn in and in this way the oil is
distributed to the cutters.
Note: This procedure is acknowledged as
follows to turn off the display after the cutters
have been oiled:
- Open the door until the control display
lights up. The control displays (7) and (4) flash.
- Press the reverse button
down until the control display
- Close the door again.
Cutting width
paper
0.23 in.
0.15 in.
0.15x1.42 in.
0.07x0.59 in.
0.03x0.47 in.
0.03x0.18 in.
Power supply data
supply voltage/frequency · current consumption · power
120V/60Hz · 12.0 amps · 1.4 kW
120V/60Hz · 12.0 amps · 1.4 kW
120V/60Hz · 12.0 amps · 1.4 kW
120V/60Hz · 12.0 amps · 1.4 kW
120V/60Hz · 12.0 amps · 1.4 kW
120V/60Hz · 12.0 amps · 1.4 kW
MALFUNCTIONS
(6) comes on.
(7) comes on proceed as follows:
(8) comes on
(7) flashes. Remove the
(4) and keep it held
(7) goes out.
TECHNICAL DATA
Cutting capacity
Working width
paper
35-38 sheets*
12.20 in.
31-33 sheets*
12.20 in.
23-25 sheets*
12.20 in.
15-17 sheets*
12.20 in.
10-12 sheets*
12.20 in.
7-8 sheets*
12.20 in.
100V/50/60Hz · 18.0 amps · 1.8 kW
100V/50/60Hz · 18.0 amps · 1.8 kW
100V/50/60Hz · 18.0 amps · 1.8 kW
100V/50/60Hz · 18.0 amps · 1.8 kW
100V/50/60Hz · 18.0 amps · 1.8 kW
100V/50/60Hz · 18.0 amps · 1.8 kW
4
Translation of the Original Operating Manual
Übersetzung der Originalbetriebsanleitung
ELECTRICAL FAULT:
If the control display
the function button (2) LED display
the control display (8)
(6)
electrical fault. The machine cannot be started.
In this case please contact your dealer.
FAULT CHECK LIST:
Should the machine not work, check the following
points:
- is the plug connected to the power supply?
- is the door closed?
- is the paper collection bag full?
Follow the instructions for "EMPTYING THE
PAPER COLLECTION BAG".
- Is there a material jam in the machine?
Follow the instructions in "MATERIAL JAM IN
THE MACHINE".
- Is the motor overloaded?
See "MOTOR PROTECTION".
If none of these test points apply, please
contact your dealer.
The cutters now start a cleaning cycle automatically
(forward and reverse run) and then switch off.
The machine is ready for use again. Should you
need to re-order the special oil see "SPECIAL
ACCESSORIES".
as well
AUTOMATIC ENERGY SAVING:
If the machine is not used for a while it automatically
switches off after about 5 minutes. The function
button (2) LED display
Press the function button briefly to turn it on again.
DISPOSING OF THE MACHINE:
Dispose
of
environmentally friendly fashion at the end
of its useful service life. Do not dispose of
any of the parts included in the machine or its
packaging with household waste.
(8)
Noise level
Dimensions
app. 57 dB(A)
21.06 x 15.55 x 38.58 in. 101.54 lb.
app. 57 dB(A)
21.06 x 15.55 x 38.58 in. 101.54 lb.
app. 57 dB(A)
21.06 x 15.55 x 38.58 in. 103.75 lb.
app. 57 dB(A)
21.06 x 15.55 x 38.58 in. 103.75 lb.
app. 57 dB(A)
21.06 x 15.55 x 38.58 in. 103.75 lb.
app. 57 dB(A)
21.06 x 15.55 x 38.58 in. 103.75 lb.
* based on A4-paper 70g/m² at 230V/50Hz
ACCESSORIES
Description
Plastic bag, 17.32x13.00x38.58x0.002 in.
Lubricant, 110 ml bottle
Note: For orders of special accessories and spare parts,
please contact your dealer.
(9) flashes together with
or only
flashes there is an
for "Ready" goes out.
the
machine
in
an
Weight
W x D x H
Order-No.
99977
88035
Publicité
