Symbols On The Machine; For Safe Operation - IKRA PCS 2525 Manuel D'utilisation

3. Symbols on the machine

For safe operation and maintenance, symbols are carved
in relief on the machine. According to these indications,
please be careful not to make any mistake.
a) The port to refuel the „MIX GASOLINE"
Position: near the fuel cap
b) The port to refuel the chain oil
Position: near the oil cap
c) Setting the switch to the "O" position,
the engine stops immediately.
Position: Front at the top of the rear
handle (near the switch)
d) Starting the engine, if you pull out the
choke knob (at the back-right of the rear
handle) to the point of the arrow, you
can set the starting mode as follows.
• First-stage position – starting mode
when the engine is warm.
• Second-stage position – starting mode
when the engine is cool.
Position: Upper-right of the chain cover
e) Adjust the oil pump. If you turn the rod
by screwdriver follow the arrow to the
„MAX" position, the chain oil flow more,
and if you turn to the „MIN" position,
less.
Position: Bottom of the power unit
f) The screw under the "H" stamp is The
High-speed adjustment screw. The
screw under the "L" stamp is The Slow-
speed adjustment screw. The screw
at the left of the "T" stamp is the Idle
adjustment screw.
Position: Left side of the rear handle
g) It shows the directions that the chain
brake is released (for the white arrow)
and activated (for the black arrow).
This chain-saw is for trained tree serv-
ice operators only.
Appropriate ear, eye, and head protec-
tion must be worn.
Use appropriate protection for foot-leg
and hand-arm.
Warning! Kickback may occur!
One handed operation of the saw can
be dangerous.
GB | Operating Instructions

4. For safe operation

Before operate the product
1. Never operate a chain saw when you are fatigued,
2. Use safety footwear, snug fitting clothing and eye,
3. Always use caution when handling fuel. Wipe up all
4. Eliminate all sources of sparks or flame (ie. smok-
5. Do not allow other persons to be near the chain saw
6. Never start cutting until you have a clear work area,
7. Always hold the chain saw firmly with both hands
8. Keep all parts of your body away from the saw chain
9. Always carry the chain saw with the engine stopped,
10. Always inspect the chain saw before each use for
11. All chain saw service, other than the items listed
12. Always shut off the engine before setting it down.
13. Use extreme caution when cutting small size brush
14. When cutting a limb that is under tension, be alert for
15. Keep the handles dry, clean and free of oil or fuel
16. Operate the chain saw only in well ventilated areas.
4
ill, or upset, or under the influence of medication that
may make you drowsy, or if you are under the influ-
ence of alcohol or drugs.
hearing and head protection devices.
spills and then move the chain saw at least ten (10)
feet [three (3) m] from the fueling point before start-
ing the engine.
ing, open flames, or work that can cause sparks) in
the areas where fuel is mixed, poured, or stored. Do
not smoke while handling fuel or while operating the
chain saw.
when starting the engine or cutting a wood. Keep by-
standers and animals out of the work area. Children,
pets, and bystanders should be a minimum of 30feet
(10m) away when you start or operate the chain saw.
secure footing, and planned retreat path from the
falling tree.
when the engine is running. Use a firm grip with
thumb and fingers encircling the chain saw handles.
when the engine is running. Before you start the
engine, make sure the saw chain is not contacting
anything.
the guide bar and saw chain to the rear, and the muf-
fler away from your body.
worn, loose, or changed parts. Never operate a chain
saw that is damaged, improperly adjusted, or is not
completely and securely assembled. Be sure that
the saw chain stops moving when the throttle control
trigger is released.
in the Operator's Manual, should be performed by
competent chain saw service personnel. (e.g., if im-
proper tools are used to remove the flywheel, or if an
improper tool is used to hold the flywheel in order to
remove the clutch, structural damage to the flywheel
could occur which could subsequently cause the
flywheel to disintegrate).
and saplings because slender material may catch
the saw chain and be whipped toward you or pull
you off balance.
spring back so that you will not be struck when the
tension in the wood fibers is released.
mixture.
Never start or run the engine inside a closed room or