Operating Elements And Connections; Safety Notes - IMG STAGELINE SCAN-20LED Mode D'emploi

All operating elements and connections de scribed
GB
can be found on page 2.

1 Operating Elements and Connections

1.1 SCAN-20LED
1 Mounting bracket
2 Locking screws for the mounting bracket (1)
3 SENSITIVITY control for music control via the inter-
nal microphone
4 Connection jack for the remote control LC-3
5 DMX signal input (3-pole XLR) for connecting a
light controller;
Pin 1 = ground, 2 = DMX-, 3 = DMX+
6 DMX signal output (3-pole XLR) for connection to
the DMX input of another light effect unit;
Pin 1 = ground, 2 = DMX-, 3 = DMX+
7 Display
8 Mains jack for connection to a socket (230 V~/
50 Hz) via the mains cable provided
9 Support for the mains fuse
Always replace a fuse that has blown by one of the
same type.
10 LED MASTER; will light up in the master mode
(operation without DMX controller or with the
remote control LC-3)
11 LED DMX; will light up when there are DMX control
signals at the DMX INPUT (5)
12 Button MENU to call the adjusting menu and to
select the menu items
13 Buttons and
menu
14 Button ENTER to activate a menu item and to
memorize an adjustment
15 LED SLAVE; will light up in the slave mode
(control via another SCAN-20LED unit)
16 LED SOUND; will shortly light up in case of music
control via the internal microphone
1.2 Remote control LC-3
The remote control LC-3 is available as an accessory
and not supplied with the SCAN-20LED.
17 Button STAND BY for deactivating the light beam;
at the same time, the mirror will go to the starting
position
18 Button FUNCTION for various functions depending
on the operating mode selected with the button
MODE (19) [
19 Button MODE for switching over between
– Stroboscope mode
The LED next to the button MODE will be off.
10
to change an adjustment in the
chapter 6.2]
– Selection of the colour of the light beam and of
the light pattern with the button FUNCTION
The LED of the button MODE will be on.
Note: For control via the remote control, there must be no
DMX signal at the DMX INPUT (5).

2 Safety Notes

The unit corresponds to all required directives of the
EU and is therefore marked with
WARNING The unit uses dangerous mains voltage
(230 V~). Leave servicing to skilled per-
sonnel only and do not insert anything
into the air vents; inexpert handling may
result in electric shock.
Please observe the following items in any case:
G
The unit is suitable for indoor use only. Protect it
against dripping water and splash water, high air
humidity, and heat (admissible ambient temperature
range 0 – 40 °C).
G
Do not operate the unit or immediately disconnect
the mains plug from the mains socket
1. if the unit or the mains cable is visibly damaged,
2. if a defect might have occurred after the unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the unit must be repaired by skilled per-
sonnel.
G
Never pull the mains cable for disconnecting the
mains plug from the mains socket, always seize the
plug.
G
For cleaning only use a dry, soft cloth, never use
chemicals or water.
G
No guarantee claims for the unit and no liability for
any resulting personal damage or material damage
will be accepted if the unit is used for other purposes
than originally intended, if it is not safely mounted or
correctly operated, or if it is not repaired in an expert
way.
G
Important for U. K. Customers!
The wires in this mains lead are coloured in accord -
ance with the following code:
green/yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug, pro-
ceed as follows:
1. The wire which is coloured green and yellow must
be connected to the terminal in the plug which is
marked with the letter E or by the earth symbol
or coloured green or green and yellow.
2. The wire which is coloured blue must be con-
nected to the terminal which is marked with the
letter N or coloured black.
.
,