Applications; Basic Adjustments; Setting The Unit Into Operation - IMG STAGELINE SCAN-20LED Mode D'emploi

3. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
Warning – This appliance must be earthed.
If the unit is to be put out of operation defini-
tively, take it to a local recycling plant for a
disposal which is not harmful to the environ-
ment.

3 Applications

The light effect unit SCAN-20LED is ideally suited for
applications on stage and in discotheques. It will pro-
ject various coloured patterns. As a light source, it has
a super bright white LED (10 W) with a low power con-
sumption and a long life.
The colours, the patterns and the movement of the
mirror will be controlled via the integrated microphone,
via the remote control LC-3 (available as an accessory)
or with a DMX controller via 6 DMX control channels.
4 Mounting
G
Always place the unit in such a way that a sufficient
air circulation will be ensured during operation.
Never cover the air vents on the housing (e. g. by
curtains).
G
The minimum distance to the illuminated object
should be 10 cm.
1) Screw the light effect unit with the mounting bracket
(1) to a suitable place, e. g. on a cross bar or a light-
ing stand.
WARNING Mount the unit safely and expertly. If
it is installed at a place where people
may walk or sit under it, additionally
secure it (e. g. by a safety rope; fas-
ten the safety rope in such a way
that, even in the event of a fall, the
maximum falling distance of the unit
will not exceed 20 cm).
2) To align the unit, release the locking screws (2).
Adjust the desired inclination of the unit, then
retighten the screws.

5 Setting the Unit into Operation

WARNING Never look directly into the light beam;
this may cause eye damage.
Please note that fast changes in light-
ing, e. g. flashing light, may trigger
epileptic seizures with photosensitive
persons or persons with epilepsy!
Connect the mains cable provided to the mains jack (8)
first, then connect it to a socket (230 V~/ 50 Hz). During
the starting phase, the display (7) will indicate
Then the unit will be ready for operation and can be
controlled via a DMX controller (
automatically change the pattern of the light beam in
the master mode ( chapter 6). To switch off the unit,
disconnect the mains plug.
For a more convenient operation, it is recom-
mended to connect the unit to a mains socket which is
switched on and off via a light switch.
Caution: Do not connect the unit to the mains voltage
via a dimmer!

5.1 Basic adjustments

Turn the lens to adjust the focus of the light pattern.
The following basic adjustments can be made via
the display (7) and the control buttons (12 – 14). For
this purpose, press the button MENU (12) so many
times until the desired function is displayed. Then
press the button ENTER (14). Make sure that the next
button is pressed within 8 seconds, otherwise the
adjusting process will end automatically. The menu
structure can be found on page 15.
Blackout mode off or on
Use the button or (13) to select:
The light beam will be permanently activated.
This adjustment must be selected when the
unit is operated without a DMX controller.
The light beam will only be activated when
there is a DMX control signal at the jack
DMX INPUT (5). When the DMX controller is
switched off, the light beam will be deactivated.
To memorize, press the button ENTER (14).
Pan of mirror normal or inverted
Use the button or (13) to select:
Normal pan of mirror.
Inverted pan of mirror. When two SCAN-20LED
units are controlled via the same DMX address,
the mirror movements of the units can be mir-
ror-inverted when the pan is set to normal on
one unit and to inverted on the other unit.
To memorize, press the button ENTER (14).
Tilt of mirror normal or inverted
Use the button or (13) to select:
Normal tilt of mirror.
Inverted tilt of mirror. When two SCAN-20LED
units are controlled via the same DMX address,
the mirror movements of the units can be mir-
ror-inverted when the tilt is set to normal on one
unit and to inverted on the other unit.
To memorize, press the button ENTER (14).
.
chapter 7) or will
GB
11