Operation Without Dmx Controller - IMG STAGELINE SCAN-20LED Mode D'emploi

GB
Display on or off
Use the button
The display (7) will always be on.
The display will be switched off approx. 60 s
after pressing the last button. It will be switched
on again the next time a button is pressed.
To memorize, press the button ENTER (14).
Display representation
Use the button ENTER (14) to select and memorize at
the same time:
normal representation
representation turned by 180°
Approx. 8 s after pressing the last button, the adjusting
menu will be exited automatically.

6 Operation without DMX Controller

When there is no DMX control signal at the jack DMX
INPUT (5), the yellow LED MASTER (10) will light up,
the display (7) will show the master mode (indication
) and the unit will automatically change the light
patterns. For this purpose, the Blackout mode must be
deactivated,
For changing the patterns, the colour of the light
beam and the movement of the light beam according
to the beat of the music, activate the music control:
1) Press the button MENU (12) so many times until the
display (7) shows
button is pressed within 8 seconds, otherwise the
adjusting process will end automatically.
2) Activate the menu item
ENTER (14). The display will indicate the operating
status:
= music control activated
= music control deactivated
The unit will automatically control the change
of patterns and colour and the movements of
the light beam.
3) Use the button
the music control and press the button ENTER to
confirm.
4) For music control, adjust the SENSITIVITY control
(3) for the microphone in such a way that the light
beam will be optimally controlled by the music. The
green LED SOUND (16) will shortly light up with
each control signal created by the sound picked up
with the microphone.
Notes
1. When the volume at the music system is modified, the
microphone sensitivity must be adapted accordingly with
the rotary control.
2. When the volume is too low or when the SENSITIVITY
control is set to the left stop, the unit will automatically
change the light pattern.
12
or (13) to select:
chapter 5.1.
. Make sure that the next
with the button
or (13) to activate or deactivate
6.1 Interconnecting several SCAN-20LED units
Several SCAN-20LED units may be interconnected in
order to control all slave units in sync with the master
unit.
1) Connect the DMX OUTPUT (6) of the master unit
via a 3-pole XLR cable (e. g. series MEC-... or
MECN-... from the product range of "img Stage
Line") to the DMX INPUT (5) of the first slave unit.
2) Connect the DMX OUTPUT of the first slave unit to
the DMX INPUT of the second slave unit, etc. until
all units have been connected in a chain.
3) Set the slave units to one of the slave modes:
a) Press the button MENU (12) so many times until
the display (7) shows
next button is pressed within 8 seconds, other-
wise the adjusting process will end automatically.
b) Activate the menu item
ENTER (14). The display will indicate the slave
mode adjusted:
Slave mode 1: The slave unit will be con-
trolled in sync with the master unit.
Slave mode 2: The slave unit will be con-
trolled opposite to the master unit.
c) Use the button
slave mode and press the button ENTER to con-
firm.
Once the control signals from the master unit are
applied to the slave units, the red LED SLAVE (15)
will light up on the slave units.
6.2 Remote control LC-3
The remote control LC-3 available as an accessory
allows to control various functions.
1) Connect the remote control to the jack ONLY FOR
REMOTE CONTROL (4).
2) There must be no DMX signal at the DMX INPUT (5).
3) Via the DMX OUTPUT (6), further SCAN-20LED
units may be connected (
control them together with the master unit via the
remote control.
4) With the button STAND BY (17), the light beam can
be activated or deactivated. At the same time, the
mirror will go to the starting position. When the light
beam is deactivated, the LED next to the button
STAND BY will light up as a check.
5) Select the operating mode with the button MODE
(19):
a) When the LED of the button MODE is off, the
stroboscope mode will be activated. By keeping
the button FUNCTION (18) pressed, one of the
three stroboscope functions can be activated:
1. permanent stroboscope
2. stroboscope activated by a music pulse and
deactivated by the next music pulse* etc.
. Make sure that the
with the button
or (13) to select the desired
chapter 6.1) in order to