Correction Of Malfunctions - Titan Control Max 1900 Pro Skid Mode D'emploi

Control Max 1900 Pro Skid

Correction of Malfunctions

Problem Cause
•
The sprayer does The sprayer is not plugged in.
•
not start. The device is switched of.
•
The sprayer was turned of while still under
pressure.
•
No voltage is coming from the wall plug.
•
The extension cord is damaged or has too low
a capacity.
•
Device overheated
•
There is a problem with the motor.
•
The spray device The unit will not prime properly or has lost
runs but does not prime.
•
suck up any paint The paint bucket is empty or the suction tube
when the selector is not totally immersed in the paint.
•
switch is set to the The suction tube is clogged.
•
PRIME position. The suction tube is loose at the inlet valve.
•
The inlet valve is stuck.
•
The inlet valve is worn or damaged.
•
The PRIME/SPRAY valve is plugged
•
The sprayer draws The spray nozzle is worn.
•
up paint but the The inlet ilter is clogged.
•
pressure drops The paint is too viscous or contaminated.
•
when the gun is The inlet valve is worn or damaged.
triggered.
•
The spray gun leaks Internal parts of the gun are worn or dirty.
•
The nozzle The nozzle was assembled incorrectly.
•
assembly leaks A seal is dirty.
•
The spray gun will The spray nozzle is plugged.
•
not spray. The spray tip is in the reverse position.
•
The paint pattern is The paint is too viscous or contaminated.
•
tailing. The spray nozzle is plugged.
•
The spray nozzle is worn.
•
The inlet ilter is clogged.
•
The inlet valve is worn or damaged.
Warranty
Titan Tool, Inc., ("Titan") warrants that at the time of delivery to the original purchaser for use ("End User"), the equipment covered
by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or extended
warranty published by Titan, Titan's obligation under this warranty is limited to replacing or repairing without charge those parts
which, to Titan's reasonable satisfaction, are shown to be defective within twelve (12) months after sale to the End User. This
warranty applies only when the unit is installed and operated in accordance with the recommendations and instructions of Titan.
This warranty does not apply in the case of damage or wear caused by abrasion, corrosion or misuse, negligence, accident, faulty
installation, substitution of non-Titan component parts, or tampering with the unit in a manner to impair normal operation.
Defective parts are to be returned to an authorized Titan sales/service outlet. All transportation charges, including return to the
factory, if necessary, are to be borne and prepaid by the End User. Repaired or replaced equipment will be returned to the End
User transportation prepaid.
THERE IS NO OTHER EXPRESS WARRANTY. TITAN HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING, BUT NOT
LIMITED TO, THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT PERMITTED BY LAW.
THE DURATION OF ANY IMPLIED WARRANTIES WHICH CANNOT BE DISCLAIMED IS LIMITED TO THE TIME PERIOD SPECIFIED
IN THE EXPRESS WARRANTY. IN NO CASE SHALL TITAN LIABILITY EXCEED THE AMOUNT OF THE PURCHASE PRICE. LIABILITY
FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES UNDER ANY AND ALL WARRANTIES IS EXCLUDED TO THE EXTENT
Remedy
➞ Plug the sprayer in.
➞ Turn the ON/OFF switch to ON (I).
➞ Perform pressure relief procedure and set selector
switch back to SPRAY
➞ Properly test the power supply voltage.
➞ Replace the extension cord.
➞ Switch the device of, turn the selector switch to the
PRIME position (vertical), remove the mains plug and
allow device to cool down for min. 30 minutes. Eliminate
the cause of overheating, e.g. covered ventilation slot.
➞ Please contact your Titan dealer.
➞ Try to prime the unit again.
➞ Reill the bucket or immerse the suction tube in
paint.
➞ Clean the suction tube.
➞ Tighten it securely.
➞ Press the inlet valve pusher. If the problem is not
solved, clean the inlet valve.
➞ Replace
➞ Please contact your Titan dealer.
➞ Replace the spray nozzle with a new nozzle.
➞ Clean the inlet ilter.
➞ Thin or strain the paint.
➞ Replace
➞ Please contact your Titan dealer.
➞ Check the tip assembly and assemble properly
➞ Clean the seal.
➞ Clean the spray nozzle.
➞ Put the nozzle in the forward position.
➞ Thin or strain the paint.
➞ Clean the spray nozzle.
➞ Replace the spray nozzle with a new nozzle.
➞ Clean the inlet ilter.
➞ Replace
GB
2 7