Correction Of Malfunctions - Titan Compact 190 Traduction Du Mode D'emploi Original

GB
Important Note regarding Product Liability!
Due to an EC ordinance in e ect since 01.01.1990, the manufacturer is liable for his product only if all parts originate from or were
approved by the manufacturer and the devices are assembled and operated correctly. The use of other accessories and spare parts
can partially or completely invalidate the liability.

Correction of Malfunctions

Problem Cause
•
The sprayer does The sprayer is not plugged in.
•
not start. The device is switched o .
•
The sprayer was turned o while still under
pressure.
•
No voltage is coming from the wall plug.
•
The extension cord is damaged or has too low
a capacity.
•
Device overheated
•
There is a problem with the motor.
•
The spray device The unit will not prime properly or has lost
runs but does not prime.
•
suck up any paint The paint bucket is empty or the suction tube
when the selector is not totally immersed in the paint.
•
switch is set to the The suction tube is clogged.
•
PRIME position. The suction tube is loose at the inlet valve.
•
The inlet valve is stuck.
•
The inlet valve is worn or damaged.
•
The PRIME/SPRAY valve is plugged
•
The sprayer draws The spray nozzle is worn.
•
up paint but the The inlet lter is clogged.
•
pressure drops The gun lter is plugged.
when the gun is
•
triggered. The paint is too viscous or contaminated.
•
The inlet valve is worn or damaged.
•
The spray gun leaks Internal parts of the gun are worn or dirty.
•
The nozzle The nozzle was assembled incorrectly.
•
assembly leaks A seal is dirty.
•
The spray gun will The spray nozzle or the gun lter is plugged.
•
not spray. The spray tip is in the reverse position.
•
The paint pattern is The paint is too viscous or contaminated.
•
tailing. The spray nozzle or the gun lter is plugged.
•
The spray nozzle is worn.
•
The inlet lter is clogged.
•
The gun lter is plugged.
•
The inlet valve is worn or damaged.
26
Compact 190
Remedy
Plug the sprayer in.
➞
Turn the ON/OFF switch to ON.
➞
Perform pressure relief procedure and set selector
➞
switch back to SPRAY
Properly test the power supply voltage.
➞
Replace the extension cord.
➞
Switch the device o , turn the selector switch to the
➞
PRIME position (vertical), remove the mains plug
and allow device to cool down for min. 30 minutes.
Eliminate the cause of overheating, e.g. covered
ventilation slot.
Please contact your Titan dealer.
➞
Try to prime the unit again.
➞
Re ll the bucket or immerse the suction tube in
➞
paint.
Clean the suction tube.
➞
Tighten it securely.
➞
Press the inlet valve pusher. If the problem is not
➞
solved, clean the inlet valve.
Replace
➞
Please contact your Titan dealer.
➞
Replace the spray nozzle with a new nozzle.
➞
Clean the inlet lter.
➞
Clean or replace the lter. Always keep extra lters on
➞
hand.
Thin or strain the paint.
➞
Replace
➞
Please contact your Titan dealer.
➞
Check the tip assembly and assemble properly
➞
Clean the seal.
➞
Clean the spray nozzle or gun lter.
➞
Put the nozzle in the forward position.
➞
Thin or strain the paint.
➞
Clean the spray nozzle or gun lter.
➞
Replace the spray nozzle with a new nozzle.
➞
Clean the inlet lter.
➞
Clean or replace the lter. Always keep extra lters on
➞
hand.
Replace
➞