Remington RM4040 Manuel De L'utilisateur page 4

Chain saw safety warnings:
• Keep all parts of the body away from the saw chain when
the chain saw is operating. Before you start the chain saw,
make sure the saw chain is not contacting anything. A
moment of inattention while operating chain saws may cause
entanglement of your clothing or body with the saw chain.
• Always hold the chain saw with your right hand on the rear
handle and your left hand on the front handle. Holding the
chain saw with a reversed hand configuration increases the
risk of personal injury and should never be done.
• Hold the power tool by insulated gripping surfaces only,
because the saw chain may contact hidden wiring. Saw chains
contacting a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric shock.
• Wear safety glasses and hearing protection. Further
protective equipment for head, hands, legs and feet is
recommended. Adequate protective clothing will reduce
personal injury by flying debris or accidental contact with the
saw chain.
• Do not operate a chain saw in a tree. Operation of a chain
saw while up in a tree may result in personal injury.
• Always keep proper footing and operate the chain saw
only when standing on fixed, secure and level surface.
Slippery or unstable surfaces such as ladders may cause a
loss of balance or control of the chain saw.
• When cutting a limb that is under tension be alert for
spring back. When the tension in the wood fibers is released
the spring loaded limb may strike the operator and/or throw
the chain saw out of control.
• Use extreme caution when cutting brush and saplings. The
slender material may catch the saw chain and be whipped
toward you or pull you off balance.
• Carry the chain saw by the front handle with the chain saw
switched off and away from your body. When transporting
or storing the chain saw always fit the guide bar cover.
Proper handling of the chain saw will reduce the likelihood of
accidental contact with the moving saw chain.
• Follow instructions for lubricating, chain tensioning and
changing accessories. Improperly tensioned or lubricated
chain may either break or increase the chance of kickback.
• Keep handles dry, clean, and free from oil and grease.
Greasy, oily handles are slippery causing loss of control.
• Cut wood only. Do not use chain saw for purposes not
intended. For example: do not use chain saw for cutting
plastic, masonry or non-wood building materials. Use of
the chain saw for operations different than intended could
result in a hazardous situation.
Causes and operator prevention of kickback:
Kickback may occur when the nose or tip of the guide bar touches
an object, or when the wood closes in and pinches the saw chain in
the cut.
Tip contact in some cases may cause a sudden reverse reaction,
kicking the guide bar up and back towards the operator.
Pinching the saw chain along the top of the guide bar may push the
guide bar rapidly back towards the operator.
Either of these reactions may cause you to lose control of the saw
which could result in serious personal injury. Do not rely exclusively
upon the safety devices built into your saw. As a chain saw user,
you should take several steps to keep your cutting jobs free from
accident or injury.
Kickback is the result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as give below:
• Maintain a firm grip, with thumbs and fingers encircling
the chain saw handles, with both hands on the saw and
position your body and arm to allow you to resist kickback
forces. Kickback forces can be controlled by the operator, if
proper precautions are taken. Do not let go of the chain saw.
• Do not overreach and do not cut above shoulder height.
This helps prevent unintended tip contact and enables better
control of the chain saw in unexpected situations.
• Only use replacement bars and chains specified by the
manufacturer. Incorrect replacement bars and chains may
cause chain breakage and/or kickback.
• Follow the manufacturer's sharpening and maintenance
instructions for the saw chain. Decreasing the depth gauge
height can lead to increased kickback.
WARNING:
instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
READ ALL INSTRUCTIONS BEFORE OPERATING
1. SAVE THESE INSTRUCTIONS - This manual contains
important safety and operating instructions.
2. Before using this product, read all instructions and cautionary
markings on the battery, battery charger, and the unit(s) powered
by the battery.
3. Do not handle the charger, including the charger plug and
charger terminals, with wet hands.
4. Do not charge the unit outdoors.
WARNING:
RM4150 batteries with this unit. DO NOT use any other type
of battery, attachment or accessory with this unit. Other
types of batteries, attachments or accessories could lead to
serious injury, property damage or damage to the unit.
NOTE: Although this unit can use the RM4130 battery, it is
not recommended. For best performance, always use an
RM4140 or RM4150 battery with this unit.
WARNING:
or RM4150 batteries with an RM4110 battery charger. DO
NOT attempt to use any other battery charger to charge
RM4130, RM4140 or RM4150 batteries. Other types of
battery chargers may cause the batteries to burst, resulting
in fire, personal injury or property damage.
WARNING:
charger to charge RM4130, RM4140 or RM4150 batteries.
DO NOT attempt to charge any other batteries with an
RM4110 battery charger. Other types of batteries may
burst, causing fire, personal injury or property damage.
4
Read all safety warnings and all
Only use RM4130, RM4140 or
Only charge RM4130, RM4140
Only use an RM4110 battery