Mark Rear Wall - Whirlpool YJMV9196CS Instructions D'utilisation

Mark Rear Wall

The microwave oven must be installed on a minimum of 1 wall
stud, preferably 2, using a minimum of 1 lag screw, preferably 2.
1. Using measuring tape, find and clearly mark the vertical
centerline of the opening.
A
A. Centerline
2. Align the center markers on the cardboard template (carton
top cap) or Wall template, to the centerline on the wall,
making sure it is level, and that the top of the cardboard
template or wall template is butted up against the bottom
edge of the upper cabinet.
NOTES:
If the front edge of the upper cabinet is lower than the back
■
edge, lower the cardboard template or wall template so that
its top is level with the front edge of the cabinet.
If the cardboard template or wall template is damaged or
■
unusable, measure and mark the wall with the dimensions
described in Step 4.
A
C
B
A. Rear wall
B. Cardboard template or Wall template
C. Top of cardboard template or wall template
must align with front edge of cabinet.
D. Front edge of upper cabinet
3. Holding the cardboard template or wall template in place,
mark both holes in the lower corners and draw a horizontal
line across the bottom edge of the cardboard template or
wall template. These represent the mounting plate's end
holes and bottom edge.
4. Remove the cardboard template or wall template and check
the markings:
Upper cabinet bottom
15⁵⁄₈"
Centerline
(39.71 cm)
14¹⁄₈"
(35.96 cm)
Mounting plate end hole
The bottom edge line must be 17
■
bottom of the upper cabinet and must be level.
The end holes must be 15
■
edge of the upper cabinet and must be on a level line with
each other. They must each be 14
centerline.
D
17⁵⁄₁₆"
(44.02 cm)
14¹⁄₈"
(35.96 cm)
Bottom of mounting plate
⁄ " (44.02 cm) from the
5
16
⁄ " (39.71 cm) from the bottom
5
8
⁄ " (35.96 cm) from the
1
8
5. With the support tabs facing forward (see illustrations in
the "Locate Wall Stud(s)" section), align the mounting plate
center markers to the centerline on the wall, making sure its
bottom edge is aligned to the horizontal line drawn in Step 3
and that the end holes are properly marked. Make sure the
mounting plate is level.
6. Holding the mounting plate in place, find the wall stud
centerline(s) drawn in Step 2 of "Locate Wall Stud(s)" and
mark at least 1, preferably 2 hole(s) through the mounting
plate, closest to the wall stud centerline(s). See figures 1,
2, and/or 3 in "Possible Wall Stud Configurations" in the
"Locate Wall Stud(s)" section. The blackened holes in the
shaded areas are ideal hole locations.
7. Set the mounting plate aside.
Wall Venting Installation Only
Upper cabinet bottom
4" (10.2 cm)
Centerline
6" (15.2 cm)
8. Mark the centerline 3/8" (1 cm) down from the bottom edge
of the upper cabinet.
9. Using measuring tape, measure out 6" (15.2 cm) on both
sides of the centerline, and mark.
10. Measure down 4" (10.2 cm) from the mark made in Step 8
and mark.
11. Using a straight edge, draw the 2 horizontal, level lines
through the marks made in steps 8 and 10.
12. Draw the 2 vertical plumb lines down from the marks made
in Step 9 to complete the 12" x 4" (30.5 x 10.2 cm) rectangle.
This is the venting cutout area.
13. Cut a 3/4" (1.9 cm) hole in one corner of the cutout area.
14. Using a keyhole saw, cut out the venting cutout area.
" (1 cm)
³⁄₈
6" (15.2 cm)
9