Commissioning And Using The Stove; Description Of The Product; Lighting The Fireplace For The First Time; Fire Lighting - Palazzetti STUFE A LEGNA Mode D'emploi

7 COMMISSIONING AND
USING THE STOVE
7.1

DESCRIPTION OF THE PRODUCT

Before proceeding, check for any "specific features of
the model" described for the stove model in question in
the enclosed "Product booklet".
7.2 LIGHTING THE FIREPLACE FOR THE FIRST
TIME
The first time you light your fireplace the flames should
burn at a moderate rate for approximately an hour to
allow complete settling of any masonry fillings on the
smoke fitting and drying of the protective materials of
the metallic parts.
7.3

FIRE LIGHTING:

• Clean the fireplace from any ash residues;
• completely open the primary air adjustment ; set the
lever to the start position; To do this you must move
the lever to the left, lift and place it on the extreme left
(fig.7.1 A);
• in the version ET4W manually position the lever to
the extreme left (scrolling is linear, there is no need to
raise it slightly) or set the power to 5 (maximum) using
the control panel (see para. 8);
• open the fire door pulling it towards yourself. Attention:
an automatic system tends to keep the door closed;
• carefully place the wood pieces inside the combustion
chamber;
• place a natural fire starter on the stack;
• add some crossed fine wood sticks;
• light the fire starter from the top and close the fire door
• keep the air vent opened to ensure a high bright flame
• slightly close the air vent only when proper grill base is
ensured; to do this you must move the lever to the right
to climb over the start position (Figure 7.1 B).
• in the version ET4W adjust the power as you to like
using the control panel (see para. 8).
Never use alcohol, benzene, kerosene or other liquid fuels
to light up the fire. Keep them away from fire. Never use
fire starting cubes derived from petroleum or of chemical
nature: they may seriously deteriorate the fireplace walls.
Only use ecological fire starting cubes.
7.4
7.5
- 7.1 -
- 7.1 -
004777430 - 18/04/2019 - PALAZZETTI - PN - Italy

KEEPING THE FIRE

Once the fire started and formed a proper grill base, load
the fireplace with regular amount of wood.
When the appliance is working, possible inflammable
materials must be placed at a distance of at least 80 cm
from the radiation surface (glass sides of the hearth).
Do not touch the painted parts during first lightings to
avoid damaging the paint finish and burn.

CONTROLLING COMBUSTION

Combustion air is adjusted by acting on the lever in the
middle of the lower front panel (fig.7.1 B); moving it to
the left increases the amount of primary air let in, and
moving it to the right decreases the amount of air let in.
Once the fire is burning it is advisable to adjust the air
based on heating needs or how long you want the load
of wood to last (fig.7.1 B).
In the version ET4W adjust the power as you to like using
the control panel (see para. 8).
In the ventilated version 230V it is recommended to not
leave the stove with the lever in the start position for
more than 10-15 minutes. This may cause damages to
the stove.
The stove is not suitable for continuous flame operation.
During stove operation you can favour the glass cleaning
using the air adjustment lever (fig.7.1 B).
By adjusting it to left you allow the entry of a greater
air flow that surrounds the glass keeping it cleaner by
preventing the deposits of soot and ash.
Do not exceed the maximum recommended load of wood.
For the management of the temperature controller Glass
GLA810 of the ventilated version 230V consult the
manual supplied with the display.
A
B
A
MAX MIN
B
max
A
B
A B
A
MAX MIN
B
max
A B
min
min
23