Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Attaching High Pressure Hose (Fig. F)
CAUTION: NEVER PULL WATER SUPPLY HOSE TO
MOVE pressure washer. This could damage hose and/
or pump inlet.
This pressure washer has a built in storage area to carry the
high pressure hose. The coiled hose is secured between the
cage and the main body.
nOTE: Uncoil the high pressure hose
prevent kinks.
nOTE: Avoid cross threading when installing the hose. Cross
threading will cause leaks.
1. To connect the high pressure hose
grip
5
, thread the hose collar
coupler
31
.
2. To connect the high pressure hose to the pressure
washer unit
8
, thread the hose collar
pressure water outlet
Attaching Garden Hose (Fig. G)
nOTE: Before connecting the garden hose to the pressure
washer unit, run water through the garden hose for thirty
seconds to clear any debris from inside the garden hose.
1. To connect a garden hose to the
pressure washer unit
garden hose
33
inside the water intake
2. Securely tighten the garden hose by hand.
nOTE: Always disconnect the garden hose after usage.
Attaching Nozzles (Fig. H)
DANGER: Risk of fluid injection. Do not direct
discharge stream toward persons, unprotected skin,
eyes or any pets or animals. Serious injury will occur.
WARNING: Flying objects could cause risk of serious
injury. DO NOT attempt to change nozzles while
pressure washer is running. Turn pressure washer unit
OFF before changing nozzles.
1. To connect a nozzle to the spray wand
connect collar
toward the spray wand and insert the
3
appropriate nozzle.
2. Release the quick connect collar to lock the nozzle in place.
3. Give the nozzle a firm tug after the quick connect collar
has locked into place to ensure the nozzle is locked
into place.
nOTE: The tips listed below might not be included with your
pressure washer but are available for purchase at an additional cost.
Common Spray Tips
Common Applications
15 ° Orange Nozzle
For brick or masonry.
25 ° Green Nozzle
For vinyl siding.
40 ° White Nozzle
For automotive washing.
Soap Nozzle
To apply detergents
Black Turbo Nozzle
For abrasive cleaning.
1
before installation to
1
to the handle
30
onto the inlet
32
onto the high
16
.
8
, place the end of the
15
.
, pull the quick
2
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Proper Hand Position (Fig. I)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the spray handle
grip
5
and the other hand on the spray handle
Correct Pressure Washer Unit Position
(Fig. A, B)
CAUTION: Before operation:
Always keep the unit right‑side up with its feet
wheels
21
on the ground as shown in Fig. B.
nOTE: Never attempt to use the pressure washer while
standing vertically, on its side, or flipped over on the ground.
Test Ground‑Fault Circuit‑Interrupter
(GFCI) Before Each Use (Fig. A)
This pressure washer is provided with a ground‑fault
circuit‑interrupter (GFCI) built into the plug of the
power‑supply cord. This device provides additional
protection from the risk of electric shock.
1. Plug the Ground Fault Circuit Interrupter (GFCI) into a
working grounded outlet.
2. The indicator at the top of the GFCI should turn green
when product is ready to use.
3. Press the "TEST" button (bottom). The green indicator
should disappear.
4. Press "RESET" button for use.
5. Do not use the pressure washer if the above test fails.
Soap Tank (J, K)
This pressure washer has a built in soap tank
1. To remove the soap tank, turn off the pressure washer
and turn off the water supply.
2. Pull trigger on gun handle to relieve any water pressure.
3. Lift the soap tank
27
4. Remove soap tank cap
appropriate detergent following the detergent
manufactures instructions.
5. Fit and tighten soap tank cap
tank
27
to the pressure washer unit.
6. To clean the soap tank
detergent back into its bottle. Use water from a garden
hose to thoroughly rinse out the tank. Empty the tank
and allow it to dry.
7. Reinstall soap tank to pressure washer unit and ensure the
soap tank is fully secured into the pressure washer unit.
4
17
27
.
out of the pressure washer unit
28
and fill with
28
before reinstalling soap
27
, empty any remaining
English
.
and
8
.
7
Publicité
Table des Matières
