Inspection / Maintenance; Manufacturer's Warranty - REMS Solar-Push I Instructions D'emploi

eng
of the plastic tank (6), check whether there are still air bubble in the
heat transfer medium. Continue the flushing process until there is no
more air in the heat transfer medium.
If the pump on the Solar-Push K does not suck in automatically, care-
fully open the bleed screw (9). As soon as the air has escaped, close
the bleed screw again immediately.
Switch off the pump (5) after the end of the filling and flushing process.
Close the boiler filling and emptying valves on the solar system. Open
the connecting valve between the solar system's two boiler filling and
emptying valves. Close the valve (4). On the REMS Solar-Push I,
reduce the pressure in the pressure hose by opening the pressure
relief valve (8). On the REMS Solar-Push K, reduce the pressure in
the pressure hose by slightly unscrewing the inspection glass on the
fine filter (7). The pressure relief valve (8) is available as an accessory
for the REMS Solar-Push K.
Caution – risk of scalding due to high media temperature.
First unscrew the pressure and suction hose on the filling and flushing
unit, and connect the open hose ends to the supplied connecting piece
in order to prevent heat transfer medium from dripping of running out
during transport.
Caution: Collect / remove and dispose of escaped heat transfer
medium.
4. Maintenance
Pull out the mains plug before carrying out maintenance or repair work!
This work may only be done by experts and trained persons.
4.1. Maintenance
Clean the pump regularly in order to prevent the pump parts from
sticking, particularly if they are not used for a n extended period. Store
the pump in a frost-proof location. Check the hose connectors for leaks
regularly.
Check the pump's fine filter (7) regularly for contamination by looking
through the inspection glass, and clean if necessary. To do this, unscrew
the inspection glass on the fine filter (7), remove the filter sieve and
clean both of them under running water or with compressed air. Replace
damaged filters.

4.2. Inspection / maintenance

This work may only be done by experts and trained persons.
5. Faults
5.1. Fault: No suction intake at the pump.
Cause: ● Mains plug not plugged in.
● Unsuitable transport medium.
● Suction line leaking.
● Suction line or fine filter blocked.
● Pressure hose shut off or blocked.
● Ball valve (4) on the tank closed or tank empty.
● Air in the pump
(only on Solar-Push K: see 3. Operation)
● Pump faulty.
● Motor faulty.
5.2. Fault: Pump does not build up any pressure.
Cause: ● Pumping head exceeded.
● Unsuitable transport medium.
● Boiler filling and drainage valve not closed.
● Fine filter blocked.
● Shut-off valve on the tank closed.
● Pump faulty.
5.3. Fault: Liquid escapes from the pump.
Cause: ● Ball valve (4) on the tank closed.
● Pump faulty.
6. Manufacturer's Warranty
The warranty period shall be 12 months from delivery of the new
product to the first user but shall be a maximum of 24 months after
delivery to the Dealer. The date of delivery shall be documented by
the submission of the original purchase documents, which must include
the date of purchase and the designation of the product. All functional
defects occurring within the warranty period, which clearly the conse-
quence of defects in production or materials, will be remedied free of
charge. The remedy of defects shall not extend or renew the guarantee
period for the product. Damage attributable to natural wear and tear,
incorrect treatment or misuse, failure to observe the operational instruc-
tions, unsuitable operating materials, excessive demand, use for
unauthorized purposes, interventions by the Customer or a third party
or other reasons, for which REMS is not responsible, shall be excluded
from the warranty.
Services under the warranty may only be provided by customer service
stations authorized for this purpose by REMS. Complaints will only be
accepted if the product is returned to a customer service station author-
ized by REMS without prior interference in an unassembled condition.
Replaced products and parts shall become the property of REMS.
The user shall be responsible for the cost of shipping and returning
the product.
The legal rights of users, in particular the right to claim damages from
the Dealer, shall not be affected. This manufacturer's warranty shall
apply only to new products purchased in the European Union, in Norway
or Switzerland.
eng