Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TE-TC 620/1 U Mode D'emploi D'origine

Danger!
It must be impossible for the cable and the coo-
ling water hose to get into the cutting area.
6. Operation
6.1 ON/OFF switch (Fig. 3/4)
•
To switch on, press the "I" on the ON/OFF
switch (16).
•
Before you begin cutting, wait until the cutting
wheel has reached maximum speed and the
cooling water pump (13) has started supply-
ing the cutting wheel with water.
•
To switch off, press the "0" on the switch (16).
6.2 Fitting the transport aids (Fig. 7 - 9)
•
Fit the transport wheels (19), the parking foot
(20) and the transport handle (18) as shown
in Figs. 7/8/9.
6.3 Fitting the stop rail and the angle stop
(Fig. 10)
•
First push the stop rail (6) onto the guides (a)
as shown and fasten.
•
Then you can push the angle stop (5) into the
guide (b) and fasten in any position.
6.4 Making 90° cuts (Fig. 11/12)
•
Slacken the handle screw (22) and push the
angle stop (5) into the required position and
set the angle to 0° degrees, then tighten the
handle screw (22) again in order to secure
the angle stop (5).
•
Then slacken the clamping screw (12) and
push it to the required position.
•
You can now move the machine head (23) by
the handle (9) to the rear.
•
Place a tile against the stop rail (6) and the
angle stop (5).
•
Switch on the machine.
•
Important: Wait until the cooling water has
reached the cutting wheel (2).
•
Move the machine head (23) by the handle
(9) slowly and smoothly forward through the
tile.
6.5 45° Diagonal cut (Fig. 11/13)
•
Set the angle stop (5) to 45°.
•
Cut as described in 6.4.
6.6 45° Lengthwise cut, "jolly cut" (Fig.14/15)
•
Loosen the star grip screw (10).
•
Tilt the guide rail (7) to the left to 45° on the
Anl_TE_TC_620_1_U_SPK7.indb 20 Anl_TE_TC_620_1_U_SPK7.indb 20
GB
angle scale (17).
•
Retighten the star grip screw (10).
•
Cut as described in 6.4.
6.7 Changing the diamond cutting wheel
(Fig. 16)
•
Pull out the power plug!
•
Remove the screw (24).
•
Swing up the guard (8).
•
Place the wrench (25) on the motor shaft and
hold.
•
Using the wrench (26), loosen the flange nut
in the direction of rotation of the cutting wheel
(2). (Caution: Left-hand thread.)
•
Remove the outer flange (27) and the cutting
wheel (2).
•
Clean the mounting flange (27) thoroughly
before fitting the new cutting wheel.
•
Install the new cutting wheel in reverse order
and tighten.
•
Important: Pay attention to the direction of
rotation of the cutting wheel!

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Remove dust and dirt from the machine at
regular intervals. Cleaning is best carried out
with a rag or brush.
•
Never use caustic agents to clean plastic
parts.
•
The trough (3) and the cooling water pump
(13) must be cleaned at regular intervals or
proper cooling of the diamond cutting wheel
(2) will not be guaranteed.
8.2 Maintenance
Lubricate all moving parts at regular intervals.
- 20 -
24.01.2022 08:26:24 24.01.2022 08:26:24