Accessories; Environmental Protection; Technical Specifications - Metabo SM 5-55 Notice Originale

en ENGLISH
If the screwdriver bit is worn/damaged or a different
fastening system is used (Philips, Pozidrive, Torx or
Square Drive), the screwdriver bit must be
changed.
- Detach the screwdriver magazine with adapter (4)
from the screwdriver (do not slacken the clamping
screw (3) ).
- Remove the screwdriver bit (5) (read the
screwdriver operating instructions).
Note:
The bit holder (5) may be removed from the
screwdriver spindle if the sealing sleeve (7) is pulled
back.
- Insert a new screwdriver bit (5) (read the
screwdriver operating instructions)
- Re-attach the screwdriver magazine with the
adapter (4) at the screwdriver (see chapter 6.1).
.
8. Troubleshooting
Problems:
• Countersink depth: see point b), d), e), h)
• Seized screws: see point b)
• Missing screws: see points c), g)
• Screws do not move: see points a), d)
• General: see points a) to i)
Troubleshooting:
a Always set the screwdriver to CLOCKWISE
ROTATION (FORWARDS).
b Make sure that the depth stop (10) is adapted to
the length of the screws used.
c The screwdriver bit (5) must be the correct
length. Always use genuine Metabo screwdriver
bits (see chapter 10. Accessories).
d If you are working with Philips screws, make
sure you use a Philips screwdriver bit. If you are
working with Pozidrive screws, make sure you
use a Pozidrive screwdriver bit.
e If you are unable to insert screws to the required
depth, adjust the knurled wheel (11) until the
screw depth is correct.
f Make sure that the screwdriver bit is attached
correctly (read the screwdriver Operating
Instructions).
g If you notice that the screw strip (13) is not being
fed in correctly (screws do not appear or are
missing), make sure that you push back the
depth stop (10) all the way and then move a
sufficient distance from the workpiece to allow
the depth stop to return to its original position.
The screwdriver magazine is loaded when
pushed down, therefore it might be filled wrongly
if not the entire stroke has been effected. Do not
set the tool down on the depth stop (10) as this
may feed in screws unintentionally.
h Hold the tool at right angles to the work surface.
The screw will not be inserted deep enough if the
tool is held at an angle that deviates from 90°
even slightly.
ENG 9. Maintenance
Recommended maintenance intervals:
10
Daily:
Check the screwdriver magazine for damage and
clean using compressed air (wear protective
goggles).
Weekly:
- Remove heavy dirt deposits manually without
using aggressive cleaning agent.
- Do no lubricate individual components.
f

10. Accessories

Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
Screwdriver tools / screwdriver bits:
(length: 180 mm)
PH (Philips) no x 180 mm (6.31582)
See www.metabo.com or the catalogue for a
complete range of accessories.
11. Repairs
Repairs to devices must be carried out by qualified
specialists only!
If you have Metabo power tools that require repairs,
please contact your Metabo service centre. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.

12. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.

13. Technical Specifications

Changes due to technological progress reserved.
Weight :
0.6 kg
Compatible screw types, in screw strip:
Plasterboard screws
Chipboard screws
Steel roofing screws
Timber construction screws
Fibreboard screws
Compatible screw dimensions:
Length(mm)= 20/25/30/35/40/45/50/55
Shank diameter (mm)= max. 5 mm
Head diameter (mm)= max. 9.5 mm
Screwdriver bits for screw drive:
PH (Philips) no. 2 x 180 mm
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).