Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
en
ENGLISH
Positions 1-6 correspond approximately to the
following no-load speeds:
1 ........ 1300 / min
2 ........ 1800 / min
3 ........ 2400 / min
The VTC electronics make material-compatible
work possible and an almost constant speed, even
under load.
8.2
Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only place
it down when the motor has come to a standstill.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate.
3
I
Switching on: Push the slide switch (4) forward.
For continuous activation, now tilt
downwards until it engages.
Switching off: Press the rear end of the slide
switch (4) and release.
8.3
Working instructions
Press down lightly on the machine and move over
and back across the surface.
9. Cleaning
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
10. Troubleshooting
The electronic signal display (7) lights up
and the load speed decreases. The coil
temperature is too high! Run the machine in
idling until the electronics signal indicator switches
off.
The electronic signal display (7) flashes
and the machine does not start. The restart
protection is active. If the mains plug is
inserted with the machine switched on, or if the
current supply is restored following an interruption,
the machine does not start up. Switch the machine
off and on again.
High-energy high-frequency interference. High-
energy high-frequency interference may result in
12
4....... 2900 / min
5....... 3500 / min
6....... 4000 / min
0
the machine switching off. In this case, please
switch off the machine, disconnect the plug and
then reinsert. As soon as the interference is
reduced, you can continue work.
11. Accessories
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
12. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
13. Environmental Protection
The sanding dust generated may contain
hazardous materials: do not dispose of with the
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2002/
96/EC on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
14. Technical Specifications
Explanation of details on page 3. Subject to
changes serving technical progress.
D
= maximum diameter of accessory
max
t
= max. permitted thickness of clamping
max,1
shank on accessory when using clamping
nut (8)
t
= max. permitted thickness of accessory
max,3
M
= Spindle thread
l
= Length of the grinding spindle
n
= No-load speed (maximum speed)
P
= Nominal power input
1
P
= Power output
2
m
= Weight without mains cable
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~
Alternating current
Publicité
Table des Matières
