Cleaning & Maintenance; Accessories; Environmental Protection; Technical Specifications - Metabo RB 18 LTX 60 Notice D'utilisation Originale

When working, please ensure that the machine is
operated at right angles to the pipe so that the belt
does not fall off the rollers.
To adjust the angle of contact, hold together the
additional handles (9).
You can adjust the cutting output by changing the
degree of pressure.
Keep the machine in constant motion because
otherwise recesses could be produced in the mate-
rial.
8. Cleaning, Maintenance
8.1 Motor cleaning
To clean the motor, apply jets of compressed air
through the rear ventilation slots of the machine
regularly, frequently and thoroughly. Here, the
machine must be held firmly.
8.2 Sanding belt replacement
- Hold the additional handles (9) together and
remove the sanding belt (10).
- Place the new sanding belt on the rollers so that
the arrow on the inside of the sanding belt is
aligned with the arrow (12) on the housing.
- Release the additional handles (9).
- Ensure that the sanding belt is completely on the
rollers.
- Adjust the belt run (see chapter 6.5).
9. Troubleshooting
9.1 Mains powered machines
- Overload protection: There is a MAJOR
reduction in load speed. The motor temperature
is too high! Allow the machine to run at idle speed
until it has cooled down.
- Overload protection: There is a SLIGHT
reduction in load speed. The machine is over-
loaded. Reduce the load before continuing to
work.
- Metabo S-automatic safety shutdown: The
machine was SWITCHED OFF automatically. If
the rate of current increase is too high (if the
machine seizes suddenly), the machine switches
off. Switch off the machine at the slide switch (8).
Switch it on again and continue to work as normal.
Try to prevent the machine from seizing.
- Restart protection: The machine does not
start. The restart protection is active. If the mains
plug is inserted with the machine switched on, or if
the current supply is restored following an inter-
ruption, the machine does not start up. Switch the
machine off and on again.
9.2 Cordless machines
- The electronic signal display (5) lights up and
the load speed decreases. The temperature is
too high! Run the machine in idling until the elec-
tronics signal indicator switches off.
- The electronic signal display (5) flashes and
the machine does not start. The restart protec-
tion is active. The machine will not start if the
battery pack is inserted while the machine is on.
Switch the machine off and on again.

10. Accessories

Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
Battery packs with different capacities:
118 V Li-Power 4,0 Ah ......................... 6.25591
18 V Li-Power 5,2 Ah ........................... 6.25592
18 V LiHD 5,5 Ah ................................. 6.25342
18 V LiHD 8,0 Ah ................................. 6.25369
Chargers: ASC 55, ASC 145, etc.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
11. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
A defective mains cable must only be replaced with
a special, original mains cable from metabo, which
is available only from the Metabo service.
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.

12. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2012/
19/EU on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
Special instructions for cordless machines:
Battery packs must not beposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-circu-
iting (e. g. by protecting them with adhesive tape).

13. Technical specifications

Explanatory notes on the specifications on page 4.
Changes due to technological progress reserved.
U = Voltage of battery pack
P = Nominal power input
1
ENGLISH en
13