Base Settings" (Model); Country Setting - GRAUPNER mx-10 Hott Manuel De Programmation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Base settings
Basic model-specifi c settings for fi xed-wing model aircraft
Before you start programming specifi c parameters,
some basic settings must be entered.
Stick mode
"MODE 1" (Throttle at right stick)
"MODE 2" (Throttle at left stick)
elev. down
full throttle
full throttle
elev. up
idle
idle
"MODE 3" (Throttle at right stick) "MODE 4" (Throttle at left stick)
elev. down
Motor Vollgas
full throttle
elev. up
idle
idle
Basically there are four possible ways of arranging the
principal control functions of a fi xed-wing model on the
two dual-axis sticks: the primary functions are aileron,
elevator, rudder and throttle (or airbrakes). Which of
these options you select depends on your individual
preferences and fl ying style.
To select the stick mode, fi rst select the transmitter
mode „ normal" with the mode switch. Turn the transmit-
ter OFF and insert the supplied programming plug into
the DATA socket on the back of the transmitter. Turn ON
the transmitter: you can now call up the desired stick
mode by cycling through the modes with a brief press of
the BIND-button:
104 Program description: base settings - fi xed-wing model
Buzzer
LED
transmitter
orange LED on Country setting
buzzers 1x
transmitter buz-
orange LED
elev. down
zers 2 times
fl ashes
The country setting is described in detail below.
transmitter buz-
orange LED on »MODE 1«
elev. up
zers 3 times
transmitter buz-
orange LED on »MODE 2«
elev. down
zers 4 times
transmitter buz-
orange LED on »MODE 3«
zers 5 times
elev. up
transmitter buz-
orange LED on »MODE 4«
zers 6 times
To choose a mode, hold the BIND-button pressed for
approx. three seconds. When you release the button, the
transmitter should emit an audible signal and the buzzer
sound stops. Switch OFF the transmitter and remove
the programming plug.
Never use the remote control with programming
connector plugged in!
Later, to check the stick mode which is programmed,
watch out for the Status-LED on the transmitter.
Stick mode
After you have set the stick mode, the country setting
must be done in a second step.
The Country setting is present in order to cater for vari-
ous directives (FCC, ETSI, IC etc.). The HoTT 2.4 radio
system features a restricted frequency band for France.
If you wish to use the RC system in France, the country
Description
setting on the transmitter must be set to "France" mode,
as described. It is essential not to use the Universal/
Universal/Europe
EUROPE mode.
County setting
To select a Country setting, you must fi rst switch the
France
transmitter off, then insert the supplied programming
plug in the DATA socket on the back and the Jumper
in the position „NO MIX" on the front of the transmitter.
Switch the transmitter on: you can now toggle between
the "GENERAL" and "France" settings by briefl y pressing
the BIND-button:
Buzzer
transmitter
buzzers 1x
transmitter buz-
zers 2 times
To choose a country, hold the BIND-button pressed for
approx. three seconds. When you release the button, the
transmitter should emit an audible signal and the buzzer
sound stops. Switch OFF the transmitter and remove
the programming plug.
Never use the remote control with programming
connector plugged in!
Later, to check the country setting which is programmed,
watch out for the Status-LED on the transmitter.
LED
Description
orange LED on Country setting
Universal/Europe
orange LED
County setting
fl ashes
France

Hide quick links:

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

33110Gr-12 hottGrp-33110.77

Table des Matières