3M Peltor Lite-Com Pro II Mode D'emploi page 8

The use of a comfortable hearing protector, designed for the specific noise level in which it is used, is the best guarantee to that you will
wear the hearing protector 100% of the time for to protect from permanent hearing loss.
The wearer shall ensure that the ear-muffs are worn at all times in noisy surroundings.
For best protection, brush aside excess hair around your ears so the cushions fit snugly to your head.
Any temples/bands of spectacles or goggles should be as thin as possible to make the hearing protector fit close to the head.
The fitting of hygiene covers may affect the acoustic performance of the ear-muffs.
MAINTENANCE
Clean the outside of the headset regularly with mild detergent and warm water.
Notice! Do not immerse in water or fluids.
After prolonged hours of use, or other situations in which the 3M™ Peltor™ Lite-Com Pro II attracts moisture inside the cups, remove
the cushions and inserts to allow the hearing protector to dry before next use.
Do not store the headset in temperatures exceeding +55°C, for example on a dashboard or windowsill.
Recommended shelf life is 5 years for the headset and 1 year for the battery from date of manufacturing.
The wearer should ensure that the ear-muffs are regularly inspected for serviceability. Ear-muffs, and in particular cushions, may
deteriorate with use and should be examined at frequent intervals for cracking and leakage, for example. For instructions how to
replace the ear cushions, see Fig. P
This product may be adversely affected by certain chemical substances. Further information should be sought from 3M.
When the low battery warning alarm sounds, it is time to replace the batteries. The unit switches off automatically after a few minutes.
Never replace or install batteries with the unit switched on. Before switching on, make sure that the batteries are inserted correctly.
As with any hearing protector incorrect use or failure to the instructions supplied with this product could result in permanent disability
due to exposure to noise.
This product is covered by the WEEE directive 2002/96/EC and is recyclable. Dispose of the product in accordance with national
regulation. Use local recycling system for electronic products
APPROVALS
MT7H7F4010-EU-50
MT7H7B4010-EU-50
MT7H7P3E4010-EU-50
All models are identical, except for the band differences and the safety helmet mounting.
3M™ Peltor™ Lite-Com Pro II headsets are ATEX and IECEx certified and approved by Nemko for use in hazardous locations.
ATEX CERTIFICATION AND LISTINGS:
I M1 Ex ia I Ma
II 1G Ex ia IIC T4 -20°C ≤ Ta ≤ +50°C Ga
II 1D Ex ia IIIC T130°C Da
ATEX
Nemko 11ATEX1234X
IECEX
NEM 11.0025X
APPLICABLE STANDARDS:
IECEX
IEC 60079-0:2007, IEC 60079-11:2011
ATEX
CENELEC EN 60079-0:2009, CENELEC EN 60079-11:2007, CENELEC EN 61241-11:2006
CE
3M™ Peltor™ Lite-Com Pro II is in conformity with the provisions set out in the PPE directive 89/686/EEC the R&TTE directive
1999/5/EC and the ATEX directive 94/9/EC.
Thereby it fulfils the requirements for CE marking.
The product has been tested and approved in accordance with EN 352-1:2002, EN352-3:2002, EN352-4:2001, EN352-6:2002,
EN62479:2010, EN 300 296-2 V1.3.1, EN 301 489-1 V1.8.1, EN 301 489-3 V1.4.1, EN 301 489-5 V1.3.1, EN 300 220-2 V2.3.1,
Head Band Version
Neck Band Version
Version with attachment for use with safety helmet
6