Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
•
Adjustment of the output pressure
•Partially unscrew the pressure output screw (
•Supply the appliance with the correct pressure specified on Table T and with nominal voltage as shown
on the rating plate.
•Start the oven as indicated in the paragraph "
A
PU
B
A
Fig. 6
Table T
HU
CH, CZ, ES, GB, GR,
IE, IT, LT, PT, SI, SK
RO
PL
AT, CH
DK, EE, FI, HR, LT,
NO, RO, SE, SI
CZ, ES, GR, IE, IT,
PT, GB, CH, SK, TR
DE
NL
PL
CY, HU, NO
BE, FR
LU
BE
FR
CY
max (*) = Pressure regulator excluded. Screwed in to the limit.
After adjusting, check the pressure value by turning the oven off and on again. Remove the manometer
tube PU and tighten down the screw
the plate with the appropriate gas type one.
:
•for the models with electromechanical
controls, remove the cap (
the pressure turning the inner screw
clockwise to increase or anti-clockwise to
reduce the pressure until level
on the table
T
•for the models with electronic controls, in
position of maximum speed, remove the
cap (
A-Fig. 6
a clockwise direction to increase the
C
pressure or in the opposite direction to
decrease and adjust to the
provided in the table . To adjust the valve
to the pressure value
speed control in the low speed mode a n d
adjust the screw piece (
clockwise direction to increase the pressure
or in the opposite direction to decrease,
while holding the nut (
CAT.
I
2H
II
2H3P
II
2H3P
II
2E3P
II
2H3B/P
G30/G31
II
2H3B/P
G30/G31
II
2H3+
G30/G31
II
2ELL3B/P
G30/G31
I
G30/G31
3B/P
II
2E3B/P
G30/G31
I
G30/G31
3B/P
I
G30/G31
3+
I
2H
I
G20/G25
2E(R)
I
G20/G25
2Esi
I
3B
.
Seal cover
PU- Fig. 6
) and connect the manometer pipe;
Instruction for use
A-Fig. 6
PU
), adjust the nut (
B-Fig. 6
PU max
T
PU min
turn the fan
C-Fig. 6
B-Fig. 6
).
PU min
GAS
p (mbar)
(mbar)
G20
25
4
G20
20
4
G31
37
17
G20
20
4
G31
30
17
G20
20
4
G31
37
17
G20
20
4
50
13
G20
20
4
28-30
13
G20
20
4
28-30/37
13
G20
20
4
G25
20
6
50
13
28-30
13
G20
20
4
37
13
28-30
13
28-30/37
13
G20
20
4
20/25
4/6
20/25
4/6
G30
28-30
13
A
with red enamel
45
";
), adjust
as shown
) in
value
) in a
BAKETEK 0564G...BAKETEK 1064G...
9/13,8 kW
PU max
A (Fig.5)
H (Fig.5)
(mbar)
Ø (1/100 mm)
H (mm)
9
340
14
9
340
14
max (*)
195
18
9
340
14
195
18
max (*)
9
340
14
max (*)
195
18
9
340
14
27,5
195
18
9
340
14
max (*)
195
18
9
340
14
max (*)
195
18
9
340
14
13
340
14
27,5
195
18
max (*)
195
18
9
340
14
27,5
195
18
max (*)
195
18
max (*)
195
18
9
340
14
9/13
340
14
9/13
340
14
max (*)
195
18
, put back the plastic cap and replace
GB
Fig. 5
A
V
H
B
11/16 kW
A (Fig.5)
H (Fig.5)
Ø (1/100 mm)
H (mm)
375
14
375
14
205
41
375
14
205
41
375
14
205
41
375
14
205
41
375
14
205
41
375
14
205
41
375
14
375
14
205
41
205
41
375
14
205
41
205
41
205
41
375
14
375
14
375
14
205
41
Publicité
Chapitres
Table des Matières
