Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL GE-CT 18/28 Li Instructions D'origine

•
To avoid unnecessary wear on the line, keep
the grass trimmer away from hard objects.
•
To use the edge guide along walls or objects,
pull the edge guide forward (see section 5.5).
Push it into the guard hood when not in use
(see section 5.5).
Using the grass trimmer as an edge trimmer
(Fig. 21- 22)
To cut the edges of lawns alongside e.g. fl ower
beds (vertical cutting), the grass trimmer can be
converted into a lawn edge trimmer.
The lock (Item 12) latches in the angle of tilt ad-
justment (Item 12a). While holding the angle of
tilt adjustment (Item 12a) in place, pull the long
handle upwards out of the lock and turn it 180°
counter-clockwise until it latches home. Tilt the
long handle as required (see section 5.4). Use the
edge guide (see section 5.5).
Return the motor head in reverse order to its ori-
ginal position in order to use it as a grass trimmer
or with the trimmer cart (only model GE-CT 18/28
Li TC).
Using with a trimmer cart
(only model GE-CT 18/28 Li TC)
•
Push the equipment.
•
Ensure that the safe distance established by
the long handle between the trimmer cart and
the user is always maintained.
•
For safety reasons the lawn mower is not
allowed to be used on inclines of more than
15 degrees.
•
Take special care when backing up and
pulling the lawn mower. Tripping hazard!
•
Tips for proper mowing
•
It is recommended that you overlap the mo-
wing swaths.
•
Always mow across inclines (not up and
down).
•
Steer the cutting in straight lines in order to
achieve a tidy look. The swaths should over-
lap each other by a few centimeters in order
to avoid stripes.
•
Select the cutting height according to the ac-
tual length of the grass. Make several passes
so that no more than 3 cm of grass are cut at
one time.
Anl_GE_CT_18_28_Li_SPK13.indb 23 Anl_GE_CT_18_28_Li_SPK13.indb 23
GB
7. Cleaning, maintenance and
ordering of spare parts
Before putting away or cleaning the grass trim-
mer, switch it off and remove the battery.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend that you clean the equipment
immediately after you use it.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may be ag-
gressive to the plastic parts in the equipment.
Ensure that no water can get into the interior
of the equipment. The ingress of water into an
electric tool increases the risk of an electric
shock.
•
Use a brush to remove deposits from the
safety cover.
7.2 Replacing the line spool (Fig. 23 – 25)
Danger! Remove the battery!
1. Press the line spool housing together at the
opposite-lying ribbed points (Item H) and re-
move the spool cover (Item 7b).
2. Remove the empty line spool (Item 7c).
3. Thread the end of the line from the new line
spool through the eyelet (Item 7d) of the
spool cover and allow approx. 10 cm of line to
project.
4. Ensure that the spool cover mounts (Fig. 7e)
and the recesses (Item K) on the line spool
lie opposite each other. Press the spool cover
back into the line spool housing.
Line spool Art.Nr.: 34.051.16
7.3 Maintenance
There are no other parts inside the equipment
which require maintenance.
- 23 -
04.03.2021 14:29:13 04.03.2021 14:29:13