Black & Decker Home Ultimate Plus B2500C Mode D'emploi page 9

Fats
Shortening, butter and oil shorten, or tenderize, the texture of yeast breads. French
bread gets unique crust and texture from the lack of fat added. However, breads
that call for fat stay fresh longer. If butter is used directly from refrigerator, it should
be cut into small pieces for easier blending during kneading process.
Baking Powder
Double acting baking powder is leavening agent used in quick breads and cakes.
This type of leavening agent does not require rising time before baking, as chemical
reaction works when liquid ingredients are added and again during baking process.
Baking Soda
Baking soda is another leavening agent, not to be confused or substituted for baking
powder. It also does not require rising time before baking, as chemical reaction
works during baking process.
Important: Ingredients must be measured with exacting accuracy to avoid
affecting taste and texture of bread.
Special Glazes for Yeast Breads
Select 1 of the following special glazes to enhance your bread.
• Egg Glaze: Beat 1 large egg and 1 tablespoon of water together, brush generously
over dough – prior to baking.
• Melted Butter Crust: Brush melted butter over just-baked bread for a softer, more
tender crust.
• Milk Glaze: For a softer, shiny crust, brush just-baked bread with milk or cream.
• Sweet Icing Glaze: Mix 1 cup sifted icing sugar with 1 to 2 tablespoons of milk
until smooth to make a consistent glaze. Drizzle glaze over raisin bread or sweet
breads when they are almost cool.
Note: If desired, generously sprinkle with your choice of poppy, sesame or caraway
seeds after glazing.
Checking Dough Consistency
lthough your breadmaker will mix, knead and bake bread automatically, when
baking bread from scratch, it is necessary to learn to recognize condition of your
dough. The ratio of flour to liquid is the most critical factor in any bread recipe,
yet most easily remedied. fter 5 to 8 minutes in Knead Stage, open breadmaker to
check consistency of dough. Dough should be in a soft, tacky ball (feel sticky like
scotch tape). If it is too dry, add ½-to-1 tsp. of liquid at a time. If it is too wet, add
½-to-1 tbsp. of flour at a time.
High- ltitude Baking
In high-altitude areas (over 3,000 feet) dough tends to rise faster, as there is less
air pressure. Therefore, less yeast is necessary. For more information on High
ltitude Baking guides contact:
Colorado Cooperative Extension Resource Center
Toll free: (877) 692-9358
E-mail: CERC@vines.colostate.edu
Website: www.ext.colostate/edu/depts/coopext
In dry climates, flour is drier and requires slightly more liquid.
In humid climates, flour is wetter and will absorb less liquid, so less liquid is
required.
16
Slicing and Storing Bread
For best results, place bread on wire rack and allow to cool for 15 – 30 minutes
before slicing. Use electric knife or serrated knife for even slices.
Store unused bread, tightly sealed (sealable plastic bags or plastic containers
work well) at room temperature for up to 3 days. For longer storage, (up to 1
month) place bread in sealed container in freezer. Since homemade bread has
no preservatives, it tends to dry out and become stale faster. Leftover or slightly
hardened bread may be cut into ½-inch or 1-inch cubes and used in recipes to
make croutons, bread pudding or stuffing.
M KING DOUGH ND B KING BRE D ND B TTER BRE DS™
Note: Depending on the Course or recipe used, some steps may not apply or there
may be additional steps. Refer to the respective Course sections in this booklet for
more detailed instructions.
Important: dd ingredients to bread pan in the order listed in the recipe.
1. Open lid and remove bread pan. Lift bread pan straight
up and out using the handle (B).
Caution: Do not turn or shake bread pan while taking it
out. If the bread pan is bent, temperature sensor may not
work properly.
B
2. Position kneading paddle on the drives shaft. Match
flat side of drive shaft to flat part of hole in kneading
paddle. Make sure paddle is secure (C).
3. Place ingredients into the bread pan. For best results,
add all liquid ingredients first, then add all dry
ingredients.
Important: lways add yeast, baking powder or baking
soda last.
C
4. Make small indentation on top of dry ingredients (not
so deep it reaches the wet layer) and add yeast/baking
powder/baking soda.
Important: Indentation for yeast is important, especially when using the delay
bake timer. It keeps yeast away from the wet ingredients until the kneading
process begins. (Liquid ingredients will prematurely activate the yeast.)
5. Insert the bread pan into the baking chamber. Press
down on rim of bread pan until it snaps securely into
place (D).
Note: If bread pan does not snap securely into place,
remove bread pan. Wearing oven mitts, place fingers
behind bread pan clips and gently pull away from oven
wall. Insert bread pan again.
D
17