Scheppach HM110MP Traduction Des Instructions D'origine page 26

5) Service
Have your power tool serviced by a qualified
a)
repair person using only identical replace-
ment parts.
This will ensure that the safety of the power tool
is maintained.
Warning!
This electric tool generates an electromagnetic field
during operation. This field can impair active or pas-
sive medical implants under certain conditions. In or-
der to prevent the risk of serious or deadly injuries,
we recommend that persons with medical implants
consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.
Safety instructions for mitre saws
a) Mitre saws are intended to cut wood or
wood-like products, they cannot be used
with abrasive cut-off wheels for cutting fer-
rous material such as bars, rods, studs, etc.
Abrasive dust causes moving parts such as the
lower guard to jam. Sparks from abrasive cutting
will burn the lower guard, the kerf insert and oth-
er plastic parts.
b) Use clamps to support the workpiece when-
ever possible. If supporting the workpiece
by hand, you must always keep your hand
at least 100 mm from either side of the saw
blade. Do not use this saw to cut pieces that
are too small to be securely clamped or held
by hand. If your hand is placed too close to the
saw blade, there is an increased risk of injury
from blade contact.
The workpiece must be stationary and
c)
clamped or held against both the fence and
the table. Do not feed the workpiece into the
blade or cut "freehand" in any way. Unre-
strained or moving workpieces could be thrown
at high speeds, causing injury.
d) Push the saw through the workpiece. Do
not pull the saw through the workpiece. To
make a cut, raise the saw head and pull it out
over the workpiece without cutting, start the
motor, press the saw head down and push
the saw through the workpiece. Cutting on
the pull stroke is likely to cause the saw blade to
climb on top of the workpiece and violently throw
the blade assembly towards the operator.
Never cross your hand over the intended line
e)
of cutting either in front or behind the saw
blade. Supporting the workpiece "cross hand-
ed" i.e. holding the workpiece to the right of the
saw blade with your left hand or vice versa is
very dangerous.
26 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Do not reach behind the fence with either
f)
hand closer than 100 mm from either side of
the saw blade, to remove wood scraps, or for
any other reason while the blade is spinning.
The proximity of the spinning saw blade to your
hand may not be obvious and you may be seri-
ously injured.
Inspect your workpiece before cutting. If the
g)
workpiece is bowed or warped, clamp it with
the outside bowed face toward the fence. Al-
ways make certain that there is no gap be-
tween the workpiece, fence and table along
the line of the cut. Bent or warped workpieces
can twist or shift and may cause binding on the
spinning saw blade while cutting. There should
be no nails or foreign objects in the workpiece.
h) Do not use the saw until the table is clear
of all tools, wood scraps, etc., except for
the workpiece. Small debris or loose pieces of
wood or other objects that contact the revolving
blade can be thrown with high speed.
Cut only one workpiece at a time. Stacked
i)
multiple workpieces cannot be adequately
clamped or braced and may bind on the blade or
shift during cutting.
j) Ensure the mitre saw is mounted or placed
on a level, firm work surface before use. A
level and firm work surface reduces the risk of
the mitre saw becoming unstable.
k) Plan your work. Every time you change the
bevel or mitre angle setting, make sure the
adjustable fence is set correctly to support
the workpiece and will not interfere with the
blade or the guarding system. Without turn-
ing the tool "ON" and with no workpiece on the
table, move the saw blade through a complete
simulated cut to assure there will be no interfer-
ence or danger of cutting the fence.
l) Provide adequate support such as table ex-
tensions, saw horses, etc. for a workpiece
that is wider or longer than the table top.
Workpieces longer or wider than the mitre saw
table can tip if not securely supported. If the cut-
off piece or workpiece tips, it can lift the lower
guard or be thrown by the spinning blade.
m) Do not use another person as a substitute
for a table extension or as additional sup-
port. Unstable support for the workpiece can
cause the blade to bind or the workpiece to shift
during the cutting operation pulling you and the
helper into the spinning blade.
n) The cut-off piece must not be jammed or
pressed by any means against the spinning
saw blade. If confined, i.e. using length stops,
the cut-off piece could get wedged against the
blade and thrown violently.