Cleaning, Maintenance, Storage And Transport; Ordering Replacement Parts; Disposal And Recycling - Scheppach HC51V Traduction Des Instructions D'origine

Please provide the following information in the event
of any enquiries:
• Type of current for the motor
Machine data - type plate
•
Machine data - type plate
•
10. Cleaning, maintenance, storage
and transport
m Important!
Pull out the power plug before doing any cleaning
and maintenance work on the equipment. Risk of
injury from electric shock!
m Important!
Wait until the equipment has cooled down com-
pletely! Risk of burns!
m Important!
Always depressurize the equipment before car-
rying out any cleaning and maintenance work!
Risk of injury!
10.1 Cleaning
Keep the equipment free of dirt and dust as far as
•
possible. Wipe the equipment with a clean cloth or
blow it down with compressed air at low pressure.
We recommend that you clean the equipment im-
•
mediately after you use it.
• Clean the equipment regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the plastic
parts in the equipment. Ensure that no water can
get into the interior of the equipment.
You must disconnect the hose and any spraying
•
tools from the compressor before cleaning. Do not
clean the compressor with water, solvents or the
like.
10.2 Maintenance work on the pressure vessel
(fig. 3)
m Important! To ensure a long service life of the
pressure vessel (2), drain off the condensed water by
opening the drain valve (1) each time after using. Re-
lease the vessel pressure first (see 10.3.1).
Open the drain screw by turning counter-clockwise
(looking at the screw from the bottom of the com-
pressor) so that all the condensed water can run out
of the pressure vessel. Then close the drain screw
again (turn it clockwise). Check the pressure vessel
for signs of rust and damage each time before using.
Do not use the compressor with a damaged or rusty
pressure vessel. If you discover any damage, then
please contact the customer service workshop.
10.2.1 Safety valve (Fig. 1 / 10)
The safety valve (10) has been set for the highest
permitted pressure of the pressure vessel.
It is prohibited to adjust the safety valve or remove
its seal.
18 GB
10.3 Storage
m Important!
Pull out the mains plug and ventilate the equip-
ment and all connected pneumatic tools. Switch
off the compressor and make sure that it is se-
cured in such a way that it cannot be started up
again by any unauthorized person.
m Important!
Store the compressor only in a dry location
which is not accessible to unauthorized persons.
Always store upright, never tilted!
10.3.1 Releasing excess pressure
Release the excess pressure by switching off the
compressor and using the compressed air which is
still left in the pressure vessel, e.g. with a compressed
air tool running in idle mode or with a blow-out pistol.
10.4 Transport (fig. 1)
The compressor can be transported by tilting to the
wheels.

10.5 Ordering replacement parts

Please quote the following data when ordering re-
placement parts:
• Type of machine
• Article number of the machine
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: clutch
* Not necessarily included in the scope of delivery!

11. Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic. De-
fective components must be disposed of as special
waste. Ask your dealer or your local council.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must
not be disposed of together with domestic
waste in compliance with the Directive
(2012/19/EU) pertaining to waste electrical and
electronic equipment (WEEE). This product must be
disposed of at a designated collection point. This can
occur, for example, by handing it in at an authorised
collecting point for the recycling of waste electrical
and electronic equipment.