Technical Data; Noise/Vibration Information; Declaration Of Conformity; Mounting And Operation - Bosch AHS 45-26 Notice Originale

OBJ_BUCH-1549-001.book Page 12 Wednesday, November 23, 2011 2:17 PM
12 | English

Technical Data

Hedgecutter
Article number
Rated power input
Cutting length
Tooth opening
No-load stroke rate
Slipping Clutch Torque
Weight according to EPTA-Procedure
01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific coun-
tries, these values can vary.
Please observe the article number on the type plate of your garden product. The trade names of the individual
garden products may vary.
Hedgecutter
Article number
Rated power input
Cutting length
Tooth opening
No-load stroke rate
Slipping Clutch Torque
Weight according to EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific coun-
tries, these values can vary.
Please observe the article number on the type plate of your garden product. The trade names of the individual
garden products may vary.

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K determined ac-
h
cording to EN 60745:
a
h
K
The vibration emission level given in this information
sheet has been measured in accordance with a stand-
ardised test given in EN 60745 and may be used to
compare one tool with another. It may be used for a
preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is
used for different applications, with different accesso-
ries or poorly maintained, the vibration emission may
differ. This may significantly increase the exposure lev-
el over the total working period.

Declaration of Conformity

We declare under our sole responsibility that the product described under
"Technical data" is in conformity with the following standards or standardiza-
tion documents: EN 60745 according to the provisions of the directives
2011/65/EU, 2004/108/EC, 2006/42/EC, 2000/14/EC.
2000/14/EC: Guaranteed sound power level
Conformity assessment procedure according to Annex V.
Equipment category: 25
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-LG/ENS,
Stowmarket, Suffolk IP14 1EY, England
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Engineering Director
Engineering PT/ESI
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
11.10.2011
F 016 L70 832 | (23.11.11)
AHS 45-26 AHS 50-26
3 600 ... H47 E.. H47 F..
W 550
mm 450
mm 26
-1
min 3400
Nm 50
kg 3.5
II
/
3 600 ...
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the expo-
sure level over the total working period.
Identify additional safety measures to protect the op-
erator from the effects of vibration such as: maintain
the tool and the accessories, keep hands warm, organ-
ise work patterns.

Mounting and Operation

Action
Delivery Scope
Connecting the Extension Lead
Starting
Stopping
Working Advice
Sawing Function
Blade Maintenance
Storage and Transport
Selecting Accessories
AHS 55-26 AHS 60-26
H47 G.. H47 H..
600 600
500 550
26 26
3400 3400 3400
50 50
3.5 3.6
II II
/ /
AHS 65-34 AHS 70-34
H47 J.. H47 K..
W 700
mm 650
mm 34
-1
min 3400 3400
Nm 50
kg 3.7
II
/
3 600 ... H47 E.. H47 J..
H47 F.. H47 K..
H47 G..
H47 H..
dB(A) 75
dB(A) 96
dB 1
2
m/s 2.5
2
m/s 1.5
3 600 ... H47 E.. H47 J..
H47 F.. H47 K..
H47 G..
H47 H..
dB(A) 97
Figure
1
2
3
3
4
5
6
6
7
Bosch Power Tools
600
600
26
50
3.6
II
/
700
700
34
50
3.8
II
/
76
97
1
4.0
1.5
98