Technical Data; Before Starting The Equipment - EINHELL BG-EH 3551 T Mode D'emploi D'origine

Anleitung_BG_EH_3551_T_SPK1:_

4. Technical data

Voltage
Power consumption
Cutting length
Cutter rail length
Tooth spacing
Cuts/min
Sound power level L
WA
Sound pressure level L
pA
K uncertainty
WA
Vibration a
hv
K uncertainty
Weight

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Fitting the hand guard
Slide on the hand guard (Figure 3a/Item 2) in the
direction indicated by the arrow (Figure 3a) Then
secure with 2 screws (Figure 3b/Item 13) (Figure 3b).
Fitting the extension bar
Undo the union nut (Figure 4/Item A) and remove
from the equipment complete with the power cable
(Figure 5a/Item 6). When fitting the extension bar,
make sure the plug-in contact (Figure 5b/Item C) is
installed in the correct direction. Then secure the
extension cable with the union nut (Figure 5c/Item
D).
Adjustable handle on the extension bar
Push the handle (Figure 6a/Item E) in the direction
indicated by the arrow and hold. You can now turn
the handle (Figure 6a/Item E) in steps of 90°.
Release the handle and make sure it locks into place
correctly. The extension bar is equipped with an
adjustable carrying strap (Figure 1/Item 12) for user-
friendly handling.
Adjustable handle on the equipment
While pressing the 2 locks (Figure 6b/Item 11) at the
same time, the handle can be turned into 5 different
positions.
Then release the locks and make sure they lock back
into place correctly. The equipment can now be
13.09.2010 10:35 Uhr Seite 11
used to cut the tops of hedges as for example shown
in Figure 6c.
230V ~ 50Hz
350 W
6. Operation
510 mm
Connect the equipment's power supply cable to the
600 mm
plug (Figure 4/Item B) and secure the power cable
8 mm
with the strain-relief clamp (Figure 4/Item 5).
2700/min
Important. To prevent accidental start-up of the
77,4 dB
equipment, the cordless hedge trimmer is equipped
90,4 dB
with a safety switch (Figure 4/Item 10) which must be
pressed before the ON/OFF switch (Figure 4/Item 9)
3.0 dB(A)
can be pressed.
4,33 m/s 2
If the ON/OFF switch is released, the equipment
1,5 m/s 2
switches off. The equipment is fitted with a safety
switch and an ON/OFF switch on both sides of the
4,7 kg
handle, enabling you to select the suitable position
depending on the work situation. The extension bar
is also fitted with a safety switch and an ON/OFF
switch with the same functions. Repeat this process
several times so that you are sure that your
equipment functions properly.
In so doing, please check the running of the
blades.
b Please check that the blades function correctly.
The blades cut on both sides and run in opposite
directions to each other, for guaranteed high
cutting performance and quiet operation.
b Fasten the extension cable to the cable holder
before starting to use the machine (see Fig. 4).
b For use in the open air you must only use
extension cables certified for the purpose.
Tips on use
b The hedge trimmer can be used not only for
trimming hedges but for trimming shrubs and
bushes as well.
For optimum trimming performance, guide the
b
blade teeth at an angle of approx. 15° to the
hedge (see Fig. 7).
b Since the blades cut on both sides and run in
opposite directions to each other, you can trim in
both directions (see Fig. 8).
b To achieve a hedge with a uniform height it is
recommended that you stretch a piece of string
along the edge of the hedge for guidance. Then
simply cut away all twigs projecting above the
line (see Fig. 9).
b The sides of the hedge should be trimmed with
arc-type movements from below upwards (see
Fig. 10).
GB
11